Tools and Equipment

how do u rethread a nut

rethread a nut for a bike

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

Have a JD lawn tractor that will not start, however it is trying and only result is a VERY loud 'back-fire'. Whats my problem? Thanks.

No further details provided

2 comments posted 14yrs

posted by JohnCig

2 comments posted 14yrs posted by JohnCig

I have a delta miter saw mod 36-075 and need the handle that houses the trigger on/off switch, help,

I have tried ereplacement parts and the other one that says they have 60,000 parts BUT not the part I need, it is part...

4 comments posted 14yrs

posted by Anonymous

4 comments posted 14yrs posted by Anonymous

3 gal harbor fright air compressor when i pull triger on nail gun the pressure dips down to low to use

is it worth rebuilding or should i deep six it . I think it might be the regulator but not sure

2 comments posted 14yrs

posted by dave E

2 comments posted 14yrs posted by dave E

where can i find homelite gas trimmer parts-line wheel,

i need the whole line housing and spring and cover

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

Recoil briggs

Recoil spring comes loose when engine starts, spring and cord still in place and attached but spring jumps out of place...

2 comments posted 14yrs

posted by Nitro

2 comments posted 14yrs posted by Nitro

Can't get the blades off, are they left handed screws?

I have a john deer riding mower, 22 hp, and need to take the blades off but the cap screws won't budge. Are they left ha...

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

Lefoo lf10-4h2 pressure swith for air compressor

I need a drawing or schematic to asemble this swith, i took it apart without realizing it was spring loaded so when I re...

3 comments posted 14yrs

posted by Exs

3 comments posted 14yrs posted by Exs

how to change traction drive belt on lt 36 lawn tractor

this belt its purpose is to drive the tractor .it runs from the top pulley to engine pulley shaft .oddly enough it the o...

2 comments posted 14yrs

posted by John

2 comments posted 14yrs posted by John

what would cause a piston and connecting rod to sheer in a stihl 4 cycle string trimmer ?

No further details provided

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

I'm exhausted from trying to start my new Husqvarna chainsaw...it FINALLY started, but why do they have to be so hard to start?

Does it help to push the bulb more than the recommended 6 times? Will it be easier in warmer weather? Do I have to lift...

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

trimmer has new plug but no spark even tried spraying staring fluid and still no start

trimmer has new plug but no spark even tried spraying staring fluid and still no start or even engine lock up, from star...

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

What kind of nails should I use? I use a nail gun

What kind of nails should I use in my nail gun?

2 comments posted 14yrs

posted by chris Butkiewicz

2 comments posted 14yrs posted by chris Butkiewicz

Lawn tractor turns two rotations on start then quits

My craftsman 18hp turns two rotations then quits,when I remove the spark plug it cranks continously

2 comments posted 14yrs

posted by Don

2 comments posted 14yrs posted by Don

looking to buy an oscillating multifunction tool - which one should I get?

Dremel looks nice but a tad expensive. I heard people mention a cheapo Harbor Freight one. Is it going to just die on m...

1 comments posted 14yrs

posted by Unsure

1 comments posted 14yrs posted by Unsure