Woodworking Forum

51629 Threads Posts
to

Restoring old wood floor, without varnish.

Hi all, I just begin to read your group, I do like to work on wood project, well will love to start a wood project, thi...
12 comments posted 22yrs
posted by francis_fillion3
12 comments posted 22yrs posted by francis_fillion3

CNC machinists in woodturning

I'm looking for people who work on CNC machines in woodturning. I work on BIMA 210. Is there anybody similliary to my ki...
4 comments posted 22yrs
posted by marcpacy
4 comments posted 22yrs posted by marcpacy

FA: Stanley Bailey No. 5 Plane - 1$

I have a Stanley Plane for auction on ebay that I am selling for a friend of mine. http://cgi.ebay.com/ws/eBayISAPI.dll...
0 comments posted 22yrs
posted by google
0 comments posted 22yrs posted by google

Laser Engraving?

Anyone here know of a good source of laser Engraving? I have a disk of Maple 3" in diameter that Id like to have some t...
2 comments posted 22yrs
posted by rob
2 comments posted 22yrs posted by rob

arbour for stacked dado

I am considering having a longer arbour made for my newly aquired Wadkin 10" sawbench, to enable use of a stacked dado...
1 comments posted 22yrs
posted by andypdq
1 comments posted 22yrs posted by andypdq

wood supplyers in UK

Hi Being an enthusiastic newbie I have bought some powertools but need some wood to cut and plane and drill holes in. C...
5 comments posted 22yrs
posted by garage.sale
5 comments posted 22yrs posted by garage.sale

General Int. 50-185 LM1 Table Saw

Oops, I clicked the wrong button before I was finished with my review of my new saw and sent it out incomplete. Anyway....
1 comments posted 22yrs
posted by theblacksheep
1 comments posted 22yrs posted by theblacksheep

My New General Int. 50-185 LM1 Table Saw

Thanks to all who replied to my info request about the GI table saw. I checked about every distributer on the West Coas...
0 comments posted 22yrs
posted by theblacksheep
0 comments posted 22yrs posted by theblacksheep

Nooitgedagt shoulder plane

Anyone tried these? I DAGS and found some references from a couple of years ago. Back then guys were paying about $50 a...
7 comments posted 22yrs
posted by donnieNoSpam
7 comments posted 22yrs posted by donnieNoSpam

Bandsaw Choices

I posted a message some time ago about going in on a bandsaw with a friend of mine and I asked this forum for advise on...
7 comments posted 22yrs
posted by woodydelsur
7 comments posted 22yrs posted by woodydelsur

Using router bits in a shaper

Shaper bits are far less expensive than cutters and can be used in the router bit collet in my Delta shaper. Are there...
1 comments posted 22yrs
posted by mspurgeon5
1 comments posted 22yrs posted by mspurgeon5

Differences between delta jointers and planers

No, not the difference between a jointer and a planer ;-) Delta has three 6" jointers in the $450-$550 range - models J...
4 comments posted 22yrs
posted by michaelpress
4 comments posted 22yrs posted by michaelpress

Places to order Shellac?

So where does everyone order Shellac flake from? My local sources have dried up and/or are nonexistent. Unless I want to...
10 comments posted 22yrs
posted by ks1911
10 comments posted 22yrs posted by ks1911

New woodworking magazine

I know there was an earlier thread on this but I don't want to retreive 77,000 threads to get there sooooo. The magazin...
11 comments posted 22yrs
posted by bchiiin
11 comments posted 22yrs posted by bchiiin