Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Plans for the Hemingway chair?

Does anyone know of building plans for a "Hemingway" chair as seen at www.laneventure.com? Actually these chairs were o...
1 comments posted 21yrs
posted by respite95
1 comments posted 21yrs posted by respite95

Dropped the motor to my Delta TS

Hello, I had an unfortunate accident where I dropped the motor from my Delta table saw (1 1/2 hp contractor saw 36-444)...
5 comments posted 21yrs
posted by jeff.pierce
5 comments posted 21yrs posted by jeff.pierce

What software to read the wreck

I'm using Outlook Express most of the time to read and post but it is not 100%. My ISP is comcast. I sometimes use goog...
3 comments posted 21yrs
posted by NunyaBiznas
3 comments posted 21yrs posted by NunyaBiznas

Table Saw

I am looking at a new table saw and I see that most of them will run 110/220v. They also say that they are pre wired to...
15 comments posted 21yrs
posted by lolsson
15 comments posted 21yrs posted by lolsson

OT: A Bandsaw and a Keyboard

Greetings! I have been too busy to spend time in the wreck but here is a link I think some of you may appreciate. ;-) ht...
37 comments posted 21yrs
posted by mark.jerde
37 comments posted 21yrs posted by mark.jerde

Craftsman align-a-rip xrc fence

I bought the aforementioned rip fence on eBay, but much to my chagrin it didn't come with anything except the fence and...
6 comments posted 21yrs
posted by crisp.dan
6 comments posted 21yrs posted by crisp.dan

Pressure Treated Wood

Is most lumber at places like Home Depot pressure treated or not? Do they always mark it if it's pressure treated? How...
3 comments posted 21yrs
posted by wizzzer
3 comments posted 21yrs posted by wizzzer

Re: I appologise...

> Sorry to hear that you consider my post as an abuse. I did not post it > with > that intencion , only because i thoug...
4 comments posted 21yrs
posted by esp
4 comments posted 21yrs posted by esp

SWMBO

What does this stand for? SWMBO
14 comments posted 21yrs
posted by ztifpatrick
14 comments posted 21yrs posted by ztifpatrick

Irvine, CA woodworker help?

I'm hoping to find an experienced wood craftsman someone in the Irvine, CA area (or just about anywhere in Southern Cal...
2 comments posted 21yrs
posted by groundzero
2 comments posted 21yrs posted by groundzero

HF 18 GAUGE, 3/8'' TO 2'' AIR BRAD NAILER

Got an email from HF today. It is currently on sale for $19.99 again. Its been a while since I've seen it at this price...
3 comments posted 21yrs
posted by jnkzs
3 comments posted 21yrs posted by jnkzs

Gloat - African Hardwood $1/bf - Portland, OR

Now that I've filled up my shop with wood, I'll share this information. I just purchased 1263 board feet of african har...
8 comments posted 21yrs
posted by mrgreg
8 comments posted 21yrs posted by mrgreg

Yet another table saw blade question

I'm looking for a combination (approx 50 tooth) standard 10" blade but I'd like to have a blade that is ground ATB with...
4 comments posted 21yrs
posted by jimREMOVETHIS
4 comments posted 21yrs posted by jimREMOVETHIS

screws or nails while building a shed

Hi all, I started a thread a few days ago about building a shed, but instead of adding this to the tail of that thread...
18 comments posted 21yrs
posted by rlangly
18 comments posted 21yrs posted by rlangly

Is it hack to mix ply with solid wood?

Making a DVD cabinet, and was thinking of saving some $$ to use oak ply for shelves and edge them. Anything wrong with...
14 comments posted 21yrs
posted by larrybud2002
14 comments posted 21yrs posted by larrybud2002