Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Floor Drill Press - Are You Using A Base?

Just curious about the feelings here in the NG. I'm switching from a benchtop DP to a Delta 16.5" floor unit, and wonde...
14 comments posted 21yrs
posted by captmikey
14 comments posted 21yrs posted by captmikey

Delta vs Ridgid vs General International

X-No-Archive: yes I'm looking to buy a contractor-style saw. I need something that can run on a 110V 20A circuit in my...
15 comments posted 21yrs
posted by bdahms
15 comments posted 21yrs posted by bdahms

small router

I had been looking for a small (smaller than a PC 690, bigger than a laminate trimmer) router. UPS delivered a Grizzly...
0 comments posted 21yrs
posted by thesameoldme
0 comments posted 21yrs posted by thesameoldme

A bit of an endorsement

All, A couple weeks ago I posted looking for a sharpening service around Baltimore. Several folks made good suggestions...
2 comments posted 21yrs
posted by gaepps1
2 comments posted 21yrs posted by gaepps1

Planer/Jointer-a relative newbie question

Hello to all. I recently came across a good deal of rough cut wood and so figured it was time to buy me a planer. As I...
7 comments posted 21yrs
posted by BillArmsTakeThisOut
7 comments posted 21yrs posted by BillArmsTakeThisOut

Gang rip tennon cheeks

I would like to get tooled up to gang rip the cheeks of a tennon in one pass. I figure that I'll need two flat top grin...
10 comments posted 21yrs
posted by sawdust.no.spam
10 comments posted 21yrs posted by sawdust.no.spam

Re: What is it? LV - new

308 Stair Guides 309 Dolly - Metalworking 310 Pencil Sharpener 311 Leather Punch? 312 Its laying on its side 313 Bone S...
9 comments posted 21yrs
posted by dave
9 comments posted 21yrs posted by dave

Grizzly G0507 band saw, any opinions?

Seriously considering the Grizzly G0507 20" band saw, I like it's size, HP, resaw cap, table size, HD frame configurati...
1 comments posted 21yrs
posted by vogeldp
1 comments posted 21yrs posted by vogeldp

"flipper" doors

Folks - Okay, this one's about WOODWORKING... not the students, this time... I am building an entertainment center, che...
3 comments posted 21yrs
posted by johnmoorhead
3 comments posted 21yrs posted by johnmoorhead

Dust collector

Im looking at getting a dust collector. Have read up on them and their importance in the shop. Still don't know which I...
5 comments posted 21yrs
posted by upick1athotmaildotcom
5 comments posted 21yrs posted by upick1athotmaildotcom

Generation X helpers

I was doing some work at a church that entailed cutting off some door bottoms to accomodate new carpeting. The church c...
7 comments posted 21yrs
posted by robert272
7 comments posted 21yrs posted by robert272

Which router to mount?

My plunge router bit the dust this week and I was thinking about buying one of those kits that contain the plunge and f...
9 comments posted 21yrs
posted by thermometer
9 comments posted 21yrs posted by thermometer

Automatic Dust Collection for My TS

I finally got the dust collection hood built for my Delta 10" open stand TS. It uses a pre-manufactured 13 x 16" fiberg...
0 comments posted 21yrs
posted by WoodworkerJoe
0 comments posted 21yrs posted by WoodworkerJoe