Tools and Equipment

What tool should I use to cut rigid insulation?

No further details provided

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

Sears Kohler 15.5 hp. at least 10 years old runs rough after it has been running a while. I have replaced the air filter, gas filter.

After cutting the grass for 20 minutes or so the mower will act like it is being starved for gas. On vary rare occasion...

2 comments posted 14yrs

posted by Michealj

2 comments posted 14yrs posted by Michealj

sears pressure washer 580.768310 info? Please!!!!

I have a sears pressure washer model# 580.768310, with a tecumseh 6.25hp # 640276. Engine number is 143.006204, family#...

1 comments posted 14yrs

posted by mvon8380

1 comments posted 14yrs posted by mvon8380

Fly wheel problem?

I just replaced my 13.5 hp Briggs and Stratton engine due to a magnet breaking off the fly wheel and ripping the altern...

0 comments posted 14yrs

posted by Lemonade

0 comments posted 14yrs posted by Lemonade

How does one know what size drill bit to use?

No further details provided

2 comments posted 14yrs

posted by ellen

2 comments posted 14yrs posted by ellen

craftsman mower 37041 ran out of gas, now won't start

craftsman mower 37041 ran out of gas, I refilled the gas tank, however the mower will not start. I've had this mower les...

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

3.5Hp lawn edger runs unevenly and at only half power. New spark plug, clean air filter, starts right up. Ideas?

engine starts right up. Definately lacks power and RPM. Seems to be getting enough gas. New magneto or spark plug wire?...

0 comments posted 14yrs

posted by Johnny E

0 comments posted 14yrs posted by Johnny E

Has anybody sucessfully opened and repaired a Sunterra 1250 pond pump?

I have a submersible Sunterra 201250 pond pump (bullet nose), it has become a little noisy and is now cutting out conti...

4 comments posted 14yrs

posted by t1man2

4 comments posted 14yrs posted by t1man2

How do I replace fuel lines on 358.356090 craftsman chain saw????

I have taken the saw apart to find a way to get the gas tank out so I can replace the vent line. I still haven't found a...

4 comments posted 14yrs

posted by Gary

4 comments posted 14yrs posted by Gary

or the threads holding the blade right or left hand threads

I can not remove the saw blade from my Dewalt portable saw. Are the threads left or right hand?

2 comments posted 14yrs

posted by Papa G

2 comments posted 14yrs posted by Papa G

how do u rethread a nut

rethread a nut for a bike

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

Have a JD lawn tractor that will not start, however it is trying and only result is a VERY loud 'back-fire'. Whats my problem? Thanks.

No further details provided

2 comments posted 14yrs

posted by JohnCig

2 comments posted 14yrs posted by JohnCig

3 gal harbor fright air compressor when i pull triger on nail gun the pressure dips down to low to use

is it worth rebuilding or should i deep six it . I think it might be the regulator but not sure

2 comments posted 14yrs

posted by dave E

2 comments posted 14yrs posted by dave E

where can i find homelite gas trimmer parts-line wheel,

i need the whole line housing and spring and cover

2 comments posted 14yrs

posted by Anonymous

2 comments posted 14yrs posted by Anonymous

Recoil briggs

Recoil spring comes loose when engine starts, spring and cord still in place and attached but spring jumps out of place...

2 comments posted 14yrs

posted by Nitro

2 comments posted 14yrs posted by Nitro