Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Remington powder driver
I have a 30 year [plus] old Rem. powder driver. I went to use it and the charges seem to have lost their strength. Is this normal? If so how does one dispose of the cartridges? Thanks, CP
8
|
5 years ago
|
8 | |
|
OT: Pressure Washer
Other options: The Karcher Promise: Cleaner. Quicker. Delivers professional level cleaning over an area 15” wide with two spinning nozzles | Cleans flat surfaces up to 4x faster than standard spray...
42
|
5 years ago
|
42 | |
|
Sofa Table
So it has been slow for me but that's OK, I do not like working in 100 degree heat with 90% humidity. A customer is down sizing and moving to a smaller home. Furniture that was in the garage is being...
2
|
5 years ago
|
2 | |
|
OT: Backer board for tile
According to our tile guy, I need 1/2" backer board to tile our floor. Does it make any difference what kind? If so, what brand do you recommend? Thanks, Mike
10
|
5 years ago
|
10 | |
|
Recess in Pinkwood[formerly called redwood]
I would like to make some 3/4" deep by 5" by 5" recesses in 2" by pinkwood 2 by 6 's. Other than with router how can this be done? The recess will only be 3 sided, cut in from one edge. Thanks CP
12
|
5 years ago
|
12 | |
|
The Storm
To those that are weathering the storm, you are in my prayers. Been there, done that, more times that I care to keep up with. It appears that the forecasters may have been a bit over cautious with...
1
|
5 years ago
|
1 | |
|
More On The "Comfortable Chair" Discussion
SWMBO and I went to a crafts festival this morning. There was a booth from a vendor named Blue Knight Windsor Chairs. I'm not sure how one becomes designated as a Master Chair Maker, but apparently...
4
|
5 years ago
|
4 | |
|
Multiple Copies with Sketchup
Just learned a new trick. Sketchup will make multiple copies at one time if you follow this process correctly: 1. Select the Move tool. 2. Press CTRL to go into Copy mode. 3. Enter the length and...
1
|
5 years ago
|
1 | |
|
Help, oak surface treatment
Cut a very detailed threshold out of 1x6 oak board. As it turns out the color of the board is perfect complement to either room. Question: What protective coating could I apply to prevent the oak from...
14
|
5 years ago
|
14 | |
|
OSHA requirment
Took a Bosch jigsaw and a Porter Cable sander to the repair shop today. The repair form I signed made me acknowledge that if they took the tools apart and decided they could not repair them that they...
17
|
5 years ago
|
17 | |
|
Anyone need a non-working RAS?
Might be a nice project, though, to get it up and running, again. Sonny https://lafayette.craigslist.org/tls/d/12-radial-arm-saw/6691074671.html
2
|
5 years ago
|
2 | |
|
plans for wooden chlothes hangers?
I realize I should have asked about this months ago, but I have been tasked with making clothing stands for small sized clothing. I keep looking at the wooden hangers which came with my suit, but...
9
|
5 years ago
|
9 | |
|
Cool Wooden Restaurant Benches - Comfortable?
SWMBO and I had a really good but way too expensive (IMO) breakfast at a restaurant in Amherst, MA. I'm more of greasy spoon diner breakfast kind of guy but this place was suggested by the owner of...
27
|
5 years ago
|
27 | |
|
Removing stainless steel trim head screws
Without going into a lot of detail, I have to remove about 200 stainless steel trim head screws from a deck made of Cambara. When I have used my power drill in the past, the heads have broken off...
35
|
5 years ago
|
35 | |
|
$50 Dust Collection Unit - Should I "Upgrade"?
This is my current dust collection system. It's crude but it works for my very small shop. I can easily swap the hose between the miter saw and a longer hose that runs along the ceiling which can be...
15
|
5 years ago
|
15 |