Woodworking Forum

51629 Threads Posts
to

Mortising Machines

Any opinions on benchtop mortising machine. I've got a used Central Machinery mortises and it takes longer to set up tha...
23 comments posted 22yrs
posted by belldoll
23 comments posted 22yrs posted by belldoll

Yorkwood 20" Planer - 1195.00 Sounds great, but.......

Hello: Thanks for reading this. I was looking at purchasing a 15" Delux Powermatic for 1595.00 when I came across this....
2 comments posted 22yrs
posted by william.hollingsworth
2 comments posted 22yrs posted by william.hollingsworth

Damn! first shop accident.

I was just taking the sanding block to a shop-made draw knife, when my block slipped off the edge of the tool, and the...
19 comments posted 22yrs
posted by tomeshew
19 comments posted 22yrs posted by tomeshew

table saw cuts - not smooth at all

I have a Craftsman 10" tablesaw. If I cut a piece of wood, and then examine the two pieces, I can see that the cut is n...
10 comments posted 22yrs
posted by gbonawitz
10 comments posted 22yrs posted by gbonawitz

Delta TP400LS Snipe

This "Virtually Snipeless" planer is sniping like a @#&^*%. I've tried extra outfeed supports and aligning the built in...
6 comments posted 22yrs
posted by bill
6 comments posted 22yrs posted by bill

OT news: West Point Fatalities?

(from RCM) http://onion.com/4006/news3.html
2 comments posted 22yrs
posted by novalidaddress
2 comments posted 22yrs posted by novalidaddress

Seattle -- bowling alleys being sold

I have no affiliation, just passing on in case anyone is looking to make a bench top or other project out of salvage bo...
1 comments posted 22yrs
posted by patja
1 comments posted 22yrs posted by patja

PING: Robert Bonomi

I tried to reply to the email you sent me, but it bounced: ----- The following addresses had permanent fatal errors ---...
4 comments posted 22yrs
posted by spambait
4 comments posted 22yrs posted by spambait

Drill press for lathe use?

Is there a device that you can put on a drill press table to allow it to act as a verticle lathe? Something that holds...
6 comments posted 22yrs
posted by trents32
6 comments posted 22yrs posted by trents32

Drill press for lathe?

Is there a device that you can put on a drill press table to allow it to act as a verticle lathe? Something that holds...
8 comments posted 22yrs
posted by trents32
8 comments posted 22yrs posted by trents32

Finish disposal and septic systems - problems?

In looking over the many choices we have as builders of furniture and what not, for finishes, I was curious what do man...
15 comments posted 22yrs
posted by mjwallace
15 comments posted 22yrs posted by mjwallace

Infinity router bits

I'm planning to upgrade a few old, lower-quality router bits. I was looking at the Whiteside line when I came across a...
3 comments posted 22yrs
posted by daz
3 comments posted 22yrs posted by daz

I finally made it to amazon.

finally got the bugs worked out and I am live. not sure how it will impact sales yet of course. I am a drip shipper rea...
29 comments posted 22yrs
posted by stevek
29 comments posted 22yrs posted by stevek

Finish on doors

I am going to replace the doors in my house with raised panel doors. I will stain and spray on a finsh of deft. My ques...
6 comments posted 22yrs
posted by not
6 comments posted 22yrs posted by not

QUESTION - is this how reforestration is done?

http://www.crazyfunnypictures.com/items/1394.jpgJOATDoing my part to piss off the religious right. Life just ain't life...
4 comments posted 22yrs
posted by Jakofalltrades
4 comments posted 22yrs posted by Jakofalltrades