Woodworking Forum

51629 Threads Posts
to

New Free Woodworking Plans Site????

Is this a new woodworking plans site? I haven't seen it before. www.freewoodplans.net
2 comments posted 22yrs
posted by noone
2 comments posted 22yrs posted by noone

glued joints require bedbolts?

Hi, I decided to go with the traditional siderails -> mortised into bedposts solution for my bed. Do I need bedbolts to...
3 comments posted 22yrs
posted by marton.czebe
3 comments posted 22yrs posted by marton.czebe

(OT) Back from the Dumpster(s)

I took a load of cardboard over to the recycle dumpster(s) behind the Gerbes store. Picked up a desktop computer case a...
1 comments posted 22yrs
posted by llhote
1 comments posted 22yrs posted by llhote

Breathing air from oilless compressors

Are the Campbell Hausefeld compressors rated for "breathing" air? I have a Gast oilless that is rated, but it is getting...
13 comments posted 22yrs
posted by gfretwell
13 comments posted 22yrs posted by gfretwell

Planing phenolic

I have some of this that I want to make a zero insert out of for my CMS. Can it be run thru a planer w/o problems. It is...
4 comments posted 22yrs
posted by oplholik
4 comments posted 22yrs posted by oplholik

An Ultimate Router Table - Part I: A Short Story

The Executive Summary: I made a router table. The Long Drawn Out Blow-By-Blow/Not Getting Out Alive Of It: It all start...
12 comments posted 22yrs
posted by UnisawA100
12 comments posted 22yrs posted by UnisawA100

CH Compressor and 220v

OK, Nearly broke my back but the new 60 gal CH compressor is bolted to the floor. 220 scares and confuses me. I have a...
4 comments posted 22yrs
posted by pfischer
4 comments posted 22yrs posted by pfischer

Good cabinet making book?

Just a rookie getting into cabinet making for my house. Bought a nice General 650 saw and slowly getting some other ess...
2 comments posted 22yrs
posted by auto119042
2 comments posted 22yrs posted by auto119042

PICTURES - Steam Sawmill

http://www.railwayeng.com/hatch/sawmill/ Not sure where this is located, the link I found it on didn't say. According t...
2 comments posted 22yrs
posted by Jakofalltrades
2 comments posted 22yrs posted by Jakofalltrades

OT - Damn Kids

Yes, yes, I know our children are the light of our lives. That's when they aren't being the bane of our existance. I ha...
16 comments posted 22yrs
posted by Jakofalltrades
16 comments posted 22yrs posted by Jakofalltrades

OT: well, not completely

Math is hard Math teaching then and now. This one has been going round the Internet for a while, but non-mathematical r...
14 comments posted 22yrs
posted by dlwinterburn
14 comments posted 22yrs posted by dlwinterburn

INCRA MITER 1000

Any opinions (pro or con) on this for my Unisaw? E-CLUB Members pay $78.95 until midnight @ Woodpeckers http://www.woodp...
4 comments posted 22yrs
posted by poseidon
4 comments posted 22yrs posted by poseidon

Nifty interactive "Workshop Planner" at Grizzly

Nobody's mentioned this yet, so I will. Grizzly sent me a little e-mail newsletter announcing their workshop planner. T...
1 comments posted 22yrs
posted by joe
1 comments posted 22yrs posted by joe

Looking for display case plans

I'm looking for plans for a table (or shelf) top display case, approximately 10"w x 8"d x 15"h, with glass on front and...
3 comments posted 22yrs
posted by warren
3 comments posted 22yrs posted by warren

Rand

has anyone heard of Rand tools? what is the quality Terry
29 comments posted 22yrs
posted by tcmusic
29 comments posted 22yrs posted by tcmusic