Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Slightly OT: Fulton Cross Cut Saw?

My father-in-law died about 3 years ago and my MIL just asked me to look through his tools to see if there was anything...
1 comments posted 22yrs
posted by toller
1 comments posted 22yrs posted by toller

Re: RESULT: rec.woodworking.all-ages passes 283:93

snipped-for-privacy@netagw.com (Bill Aten) wrote in news: snipped-for-privacy@isc.org: > RESULT > unmoderated group rec....
29 comments posted 22yrs
posted by bwr607
29 comments posted 22yrs posted by bwr607

The gloat that got away

Yesterday I am checking the clearance center at Lowes for power tools... They have a new in box Hitachi set: 18v drill...
34 comments posted 22yrs
posted by arwomack01
34 comments posted 22yrs posted by arwomack01

Dating Furniture by machine cut dovetails

I have a nice walnut dresser with obviously machine cut half blind dovetails in the drawers, both front and back. Any ru...
4 comments posted 22yrs
posted by brian_j_roth
4 comments posted 22yrs posted by brian_j_roth

Rewire Jet SuperSaw for 230V?

Just got 240V service in the garage. I'll get around to rewiring the saw from 110 to 220V. I *recall* hearing or readin...
2 comments posted 22yrs
posted by patrick
2 comments posted 22yrs posted by patrick

FYI: Leather for strop sharpening

Just to let you all know, for those that sharpen their own chisels and plane cutters, there is a seller with the best l...
6 comments posted 22yrs
posted by ahem
6 comments posted 22yrs posted by ahem

Board n' Baton siding question

When putting board n' baton siding on a building, and the boards aren't long enough to go from top to bottom, what is t...
6 comments posted 22yrs
posted by bryanNOSPAMb
6 comments posted 22yrs posted by bryanNOSPAMb

JDS Dust Force - rewire to 220V question

Hi all: I recently purchased a JDS Dust Force Dust collector and want to rewire it to 220 V as it uses 16 AMPs at 110V....
1 comments posted 22yrs
posted by juergen
1 comments posted 22yrs posted by juergen

Photos -- Knee Operated Kill Switch

Today I made a knee operated kill switch for my Jet table saw. Here is a photo of the finished switch: http://home.eart...
9 comments posted 22yrs
posted by kvaughn65
9 comments posted 22yrs posted by kvaughn65

woodworkersjournal

ANyone besides me getting the "www.woodworkersjournal.com not found" message when attempting to browse to Rob's site fro...
5 comments posted 22yrs
posted by dlwinterburn
5 comments posted 22yrs posted by dlwinterburn

Glueing ply to ply ???????

Hello, I want to attach 1/4 maple ply to the exterior of some 1/2 " plywood cabinets, should I use contact cement or reg...
7 comments posted 22yrs
posted by noname
7 comments posted 22yrs posted by noname

Wire thickness

Just built a WW shop about 50' (cable length) from my service panel. What gauge wire should I be using? 4-4-4-6? If so,...
23 comments posted 22yrs
posted by Elmar66
23 comments posted 22yrs posted by Elmar66

Building Wood Folding Stools(an Update)

You might have already seen over on alt.binaries.pictures.woodworking some pictures and posts about my present mood abo...
1 comments posted 22yrs
posted by llhote
1 comments posted 22yrs posted by llhote

Question 'help'

I am using a Forstner 1 1/4" bit trying to drill a hole 1/8th" deep in a piece of 2"x2" x 1/4" birch ..... the wood bur...
12 comments posted 22yrs
posted by ramps
12 comments posted 22yrs posted by ramps