Latest threads in Woodworking Forumshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Cutlist Software
I have been ENQ on Google at different Cutlist software: Cutlist Plus, CabinetCruncher, etc. and would like you thoughts and recommendations on the best fit for me. I am doing a variety of projects...
8
|
17 years ago
|
8 | |
|
|
Joining MDB boards.
I wish to join two MDB boards. Actually the boards look like MDB and the surfaces are grain printed. I would like to peg the boards but I do not have accurate equipment. I do have a DeWalt slot maker...
—
|
17 years ago
|
— | |
|
|
Senco SFN30 finish nailer
I have all but decided - I think. I picked up one of these at a local store and loved the weight and feel compared to other 15 gauge nailers. Its only drawback that I see is it will only shoot up to...
1
|
17 years ago
|
1 | |
|
|
Someone's trash... / Gloat application
I don't know if it qualifies as a gloat but I found a little treasure this morning. On my way to Home Depot, I drove by the neighborhood... Someone just prune his maple and they cut some fairly large...
12
|
17 years ago
|
12 | |
|
|
Hand tingles from using vibrating tools
I was wondering if it's normal for your hand to tingle for a few days after using sanders, grinders or tools that vibrate a lot. I only use them occasionaly around the house but the tingles can go on...
23
|
17 years ago
|
23 | |
|
|
Birdhouse plans on line?
I am looking for some sites that have detailed plans for birdhouses. Can anybody recommend some good sites? Thanks in advance.
3
|
17 years ago
|
3 | |
|
|
Blow Molded cases
What, if anything, are they good for after the tool has a home in the gar...shop? NOT EVER gonna move again. And that's only reason I can think of.
6
|
17 years ago
|
6 | |
|
|
Overarm pin router?
that's what it looks like to me. Surely, one of the ww'ers in the Chicago area needs one of these for $245. And, no, I have no interest in this at all other than it looks like a good deal for someone...
6
|
17 years ago
|
6 | |
|
|
Need Help with my Freud FT2000E Router
I haven't used my Freud FT2000E for a while and I now find that the 1/2" collet sticks when I try to remove a bit. The nut comes completely un-threaded and the collet stays in tightly. I guess I'm...
11
|
17 years ago
|
11 | |
|
|
removing veneer on dining table top ?
I have an older but good table that has a lot of scratches and 'tears' on the surface. If I go ahead and replace the veneer...should I sand the old top of..or...try to l"delamination' it with a heat...
1
|
17 years ago
|
1 | |
|
|
Re: Handwheels for Craftsman table saw
try 1-800-252-1698 or part number ha changed to 977227-001. the price is 10.49, a small price to pay verses modifying somethin yoursel -- glikness http://www3.sears.com/.the
3
|
17 years ago
|
3 | |
|
|
Donkey Kong Decisions
What part of "rec.woodworking" did you not understand? B.
2
|
17 years ago
|
2 | |
|
|
Cutting Thick With Small Tools
wrote in news:1162731983.739733.19660 For round stock, a lathe and a cut-off tool.
16
|
17 years ago
|
16 | |
|
|
Ping Robatoy
Hi, Thanks for your answer on a Fein sandpaper alternative. It's good to hear that I will not need a special backing pad. Do you have a source for Abranet in the GTA? Or do you have a preferred US...
8
|
17 years ago
|
8 | |
|
|
RE: A Question
Am building a chest of drawers as follows: Drawer sides and backs are 1/2 hard maple. Drawer fronts are 3/4 hard maple. Drawer bottoms are 1/4 birch ply. Drawers are to be assembled using half blind...
26
|
17 years ago
|
26 |