glass discs?

Must they be glass Norman?

polycarbonate or perspex perhaps?

Bob

find some 35mm diamiter glasses, as in the type you drink out of, and remove the tall portion leaving just the base?

Any cheap torches available ?

i remember about three years ago when looking for glass disks for my waste oil burner .. the local glass guy showed me a card with samples on ..

these were about the diameter you want .. and if i can remember they had pilkington written on the card.

they were not big enough for my use ..i ended up buying candle thingies from woolworths.

if you want a lot of them ..then a trip to St-Asaph business park North Wales maybe will yield results.......thats were the UK optical industry is, including specialist branches of pilkington and many other optical companies.

Lot of top secret stuff goes on there ..so don't be expect to get past the gates at a few of the companies.

all the best.markj

If you only need a dozen, could you not pay him to make them for you?

Other options would include an "ordinary" glass merchant of the type that does glass cut to size. They can usually do round windows, clock glasses etc, and hence may be able to do small sizes.

If that fails how about cutting your own? A wet tile cutter may do the trick. Alternatively a good diamond glass cutter with a trammel to make your scored circle, then a few radial cuts away from it before tapping or heating/cooling to snap off the segments.

Another option might be to cut a polygon with straight edges just a bit over size and then grind it down to the final fit using a carborundum stone.

Does it need to be glass? It would seem an ideal application for acrylic sheet, such as Perspex.

For example:

I tried cutting glass on my wet tile cutter. It did cut, but chipped quite badly. I assumed any glazier could make them though.

NT

If you are prepared to make them yourself then a diamond core drill in a drill press will do the job - you'll want to drill slowly and with lots of water to cool the work. If the ones you had were chipped then they were either drilled too fast, without adequate cooling or the core drill was worn out...

To buy off the shelf - you want to talk to people who supply material for glass fusing (jewellery - that sort of thing)

One supplier is Delphi Glass - they are in the USA and have 'micro-thin

I made something similar as filters for some led lamps for somebody recently - they were in pale yellow- but clear would be just as easy....

Drop me an email if you'd like to chat about it ( snipped-for-privacy@inspired-glass.com). I'm in Ireland - but postage shouldn't be too much of a problem..

Adrian

Norman,

Relatively easy to cut them yourself. Turn up a copper 'tube' with an inside diameter of the required disk. Mount in vertical mill, place glass sheet on cardboad and secure. Build a dam of putty or plastecene where the hole is needed, fill with light oil. Lower copper tube at low revs into oil having charged the copper with carborundum powder (valve grinding paste). You need to use hand quill feed or a light spring so as not to press too hard. Suprising how quickly it cuts.

BUT - if they are for toys is plain glass good enough - should it not be toughened or perhaps polycarbonate?

AWEM

Are you allowed to use glass in toys at all nowadays?

Interesting that, but can you get 35mm copper tube?

Andrew said "turn up a copper tube" ie on a lathe.

Bob

How about trying your local welders suppliers , we used to wear cutting goggles with replaceable clear glass lenses ?

Clockmakers' suppliers Meadows and Passmore list 2mm flat glass rounds, and will do special sizes for orders of 10 or more.

Tempus, in Exmouth, do very clever stuff with glass - bevelled edges, fitting to bezels, and so on, as well as flat circles. No web site, so

You're looking at over 3 quid each for either of those places.

Yes, copper tubes go a long way above the 15, 22, 28mm sizes used domestically ... 35, 42, 54, 67, 76, 108, 133, 159 and 219mm are available.

If they are still going, Chance Glass in Great Malvern used to knock similar glass blanks out at reasonable prices. I've just checked the web and they still appear to be in business:

Ah. Didn't know that - thanks.

These any good? Ebay #230399010663 they are the glass discs for a hammer break glass emergency switch. 20 for $20. You might need to ask the size/thickness. JC

I tried cutting glass on my wet tile cutter. It did cut, but chipped quite badly. I assumed any glazier could make them though.

NT

OK, time for me to but in! Amateur telescope makes do this all the time! First, never try to just do one piece of glass, you need a stack. The outer pieces should be discarded. One good way is to embed the stack of glass in plaster of paris. No need for a diamond hole saw, a simple cutter can be made from sheet metal, formed into a tube. You will need some slits in it. The actual cutting media is carborundum grains obtainable from lapidary/rockhound shops, or amateur telescope maker suppliers. Use ordinary plasticine to form a dam around the area the cutter will enter. Make slurry of carbo and water, and run the cutter slowly, with gentle downward pressure. You will have a stack of glass disks in no time. The outer ones will be chipped a bit, the inner ones should be near perfect.

Steve R.