Gate hook security pin

I'd go for a padlock; bent pins can be unbent.

My hinges didn't have anything like that. What I did was to fit an anti-lift block to the gate, under the pin bracket. I fitted it to the edge of the gate in such a way that you can only get to the screws when the gate is open.

If it is *really* like that then one option is to invert one of the hinge pins so that all the weight is taken on the other. (All the weight will normally be on one of them anyway). Another, as Colin says, is to fit some sort of anti lift block. Mainly, you are buying time. On farm gates people sometimes fit a "bike lock" chain and padlock around the gate and post, but that will look untidy.

Chris Hogg wrote on 31/01/2018 :

Not so easy to remove when you need to, but the top of our hinge pins are threaded, then a nut is fitted on top, which is then welded on top. The nuts are only screwed partially on, leaving a well at the top of the thread, into which a weld can be made. At the very least, an angle grinder would be needed to chop off the top of the nut.

I'd be inclined to tap the holes and use a stainless steel hex socket headed screw so that it will need an allen key to remove it.

You can't stop a determined thief but you can discourage opportunists.

Pop-rivet? Easily enough drilled out if you need to remove gates, but doesn't draw too much attention to the fact that there's only a weak deterrent there.

Indeed you may be able to get an appropriate "security headed" screw. The bits are widely available, but every little helps.

I just used split pins, but then I only have a garden gate and the folk who lift it off are usually youths who have been out on the beer I suspect. Brian

Many thanks for all the replies. Lots of useful suggestions there, but my first thought is a small padlock as it's simple, assuming I can find one that has a shackle that will fit. I also like the idea of tapping the hole and using a SS bolt with a hex socket head. An anti-lift block is a different approach, but I don't think it would work in my case, but I'll have to think about it. Thanks again everyone.

Surely a small padlock will be no deterrent to anyone prepared to steal a gate? Given that they?ll be coming with a vehicle, trailer, mate to help out etc, why wouldn?t they throw in a bolt cropper or other cutting device?

How big/valuable is this gate?

Tim

round here, gates are often removed and then dumped some distance away by people on their way back from the pub. They won't have any tools with them.

I doubt that much would stop a determined thief; it's more to deter the casual scrote who acts on the spur of the moment.

A padlock that's been out in the rain for a few years will need to be cut off when you want to remove the gates.

I've had padlocks out in a highly corrosive salt-rain environment for nearly twenty years with no problems, where other exposed steel, even nominally galvanised stuff, rusts away to nothing. The trick is to open them periodically and keep them oiled.

A lot of faff, considering the gate may not need to be removed at any time in the twenty years. Plus, I'd undoubtedly lose the damn keys, and padlocks that small tend to be very insecure - perhaps just as well if you lose the keys!

Just put a chain on the gate, attach it to the vehicle and drive away. A determined thief doesn't care what damage is done.

Harry Bloomfield submitted this idea :

My own gates, I had to design the hinges so the back end rose up as it was open (opening in to a slight rise in my drive). Which meant if they were opened by someone who wasn't aware, they would swing out into the road. I couldn't put a centre stop in, to stop them being opened out and the risk of being hit by passing traffic. Often posties and take-away menu delivers would try to come in via these drive gates and leave them swinging in the road, rather than use the garden gate directly alongside.

A padlock could be easily fitted, but that involved messing about with keys. I finally resolved the problem by using a cheap spring (3x for a pound) carabiner. The carabiner defeats most peoples attempts to come deliver via the wrong gate.

Likewise, it doesn't take that much to defeat thieves who will simply seek out an easier target. Nothing can be made proof against theft, you can only make it less appealing.

In message , Chris Hogg writes

A couple of agricultural solutions...

Whack in a suitably sized roll pin over a close fit washer. Can be hammered out but you need to carry a suitably sized punch as well as the hammer.

More commonly turn the top hinge over.

First on my list to try if I can't find suitable padlocks. Thanks.