Tools and Equipment

where can i find info on old disston pocket knives?

Looking for info on antique disston pocket knives

0 comments posted 14yrs

posted by Bret

0 comments posted 14yrs posted by Bret

Is there a product that will disspell water from a vehicle gas tank

Is there a product that will disspell water from a vehicle gas tank, as in M/C's

0 comments posted 14yrs

posted by Eric

0 comments posted 14yrs posted by Eric

Have Guardian/Generac 7K standby generator 7 yrs; recent problem: Starts weekly excercise, runs 20 seconds, shuts off; low oil lite on.

Also have replaced oil pressure sending unit along with oil change & filter. It will run about 1 min. when restarting,...

0 comments posted 14yrs

posted by JWAYNE

0 comments posted 14yrs posted by JWAYNE

Generac 7550

I have a Generac 7550, it has been sitting for awhile but when I start it and it starts easily (electric or pull) the g...

0 comments posted 14yrs

posted by John

0 comments posted 14yrs posted by John

how to replace a fuel shut off on a generator

I have a brigg generator the fuel shut off piece under the gas tank popped off how do i replace it

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

Ineed to find a capacitor for my Dremel Scrollsaw Motor

I need to buy a capacitor for my Dremel Scroll saw motor, it is a LAI , 250 volt .AC 12uf+10% -5%

4 comments posted 14yrs

posted by Keith

4 comments posted 14yrs posted by Keith

belmont barber chair hydralic repair

chair is stuck at top will not release to go down

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

No gas to spark plug - craftsman 32cc Craftsman Weedwacker

I read the suggestions you folks posted concerning another Sears weedwacker but it gave me no ideas. Here is what I hav...

2 comments posted 14yrs

posted by Don Peru

2 comments posted 14yrs posted by Don Peru

Has anyone used a Mapp Torch for melting silver?

What type container was used? What procedures were used?

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

Chainsaw Screws??

I have a 42cc 18" Craftsman chainsaw I disassembled out of curiosity when it was deemed unfixable by Sears, and didn't...

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

Gas pressure washer won't start

I can't pull the gas pressure washer cord to start. Remove underneath where shaft goes into pump. The flywheel only make...

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

How do I change the belt on my Delta 46-700 Lathe?

I have already cut the old belt off. I have tried a link belt and it didn't work. So I am up a creek until I get the new...

0 comments posted 14yrs

posted by Don

0 comments posted 14yrs posted by Don

cud cadet Kohler model 1681 will run at idle speed only will bog and shut off when any more throttle past idle is applied

Took off carb and cleaned it (very little dirt and no gunk) replaced carb same condition.

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous

need gasket for harbor freight compressor, anybody know where i can order

hey guys, first post. I have a harbor freight compressor, 4hp 10gal model 90234. I have a blown head gasket and cant se...

2 comments posted 14yrs

posted by Hugeroost

2 comments posted 14yrs posted by Hugeroost

I have curved shaft stihl weed eater. I got it tangled up in a wire fence. The head separated from the shaft and wont stay on

No further details provided

0 comments posted 14yrs

posted by Anonymous

0 comments posted 14yrs posted by Anonymous