Is annual furnace service worth it when the tech only wipes the igniter?

Nov 19, 2026 Last reply: 14 hours ago 5 Replies
Saved reading

First reply

SlateNomad817

First thing, before anything else: get carbon monoxide detectors if you don't already have them. With any gas furnace that's non-negotiable, and it's cheap insurance regardless of how often you service the unit. Now, on the service itself. Three minutes and a wiped igniter is…

Read the full reply

So I've got a natural gas furnace that's about three years old now, and when I got it I was told to have it serviced every year. Fine, sounds reasonable. But I'm starting to wonder what's actually supposed to be included in one of these visits. Here's why I'm asking. The last two years I paid $180 each time, and both visits were basicly identical. The guy pulls out the igniter, wipes it off, puts it back, done. I'm not exaggerating when I say the whole thing took less than 3 minutes, prolly less. For $180. It kind of feels like I'm paying for a wipe with a cloth. The furnace is still pretty new, so I get that there's not much to wear out yet. But is this normal? Do these checkups ussually involve more than that, like actual inspections or cleaning I should be expecting? And would it be reasonable to stretch it to every other year untill the unit gets older, or should I just keep paying for the annual visit?


First thing, before anything else: get carbon monoxide detectors if you don't already have them. With any gas furnace that's non-negotiable, and it's cheap insurance regardless of how often you service the unit. Now, on the service itself. Three minutes and a wiped igniter is not a tune-up. I do maintenance work myself and a proper visit takes me 45 minutes to an hour, minimum. It should include a combustion test, checking amp draws, checking the capacitors, cleaning the flame sensor, brushing out the inside of the unit, and then the part I consider the most important: cranking the thermostat up and watching the furnace run for at least 20 minutes straight. You learn a lot just watching a full cycle.

So no, what you got for your money is not normal, and I don't blame you for feeling like you paid for a wipe with a cloth. At full price you should expect way more than that.

As for frequency, on a young furnace like yours, every two to three years is honestly reasonable. Furnaces don't need much when they're new. Where annual service really starts earning its keep is once the unit gets up around 10 years old and parts actually start wearing. If it were mine at three years old, I'd probably stretch it out and save the money for now. One suggestion though: when you do book the next one, ask upfront what's included and whether they run a combustion test. If the answer sounds like 'we clean the flame sensor and check it over', keep shopping. A company that can't tell you what they're doing for the money usually isn't doing much.

I'm not so sure about stretching it to every two or three years on a young furnace. The bit that makes me hesitate is the warranty angle. A lot of manufacturers want proof of yearly maintenance, and if anything does go wrong at year four, the company could ask for service records. Show up with gaps and you might be paying out of pocket for a part that should have been covered.

Also, I'd want to know what the furnace manual actually says before skipping years. Mine spells out what counts as proper maintenance, and it's not just a wipe and a look. Did yours come with anything like that?

Lurker here finally making an account because this thread is exactly my situation, a young gas furnace and a service visit that felt way too short. The warranty point is what's keeping me from stretching it out, since I'd hate to lose coverage over a paperwork gap. My question is about the 20 minute run test you mentioned. Is that something the tech does while I'm standing there, or can I just ask them to explain what they listened for when it's done? I'd honestly have no clue what normal sounds like yet, which is probably half the reason I feel lost booking these visits.

I'd add one thing to the 'learn how it sounds when running normally' point, because it's saved me worry more than once. My own furnace is a few years old and the first couple of winters I did the yearly clean myself, flame sensor and all. After watching it fire up a handful of times I got to know the normal hum and the little click sequence it does before the burners light. Now when anything sounds even slightly off I notice it right away, instead of wondering if I'd just been ignoring it. That familiarity is a real part of maintanence, even on a young unit that barely needs anything else.

One pedantic thing I want to flag, because it bugs me every time this comes up: the part that normally needs a yearly clean is the flame sensor, not the igniter, so even the single item that got wiped on your visits may not have been the one that actually matters for reliable firing. Separate question for you, since it changes what a yearly visit should involve: is your unit a high-efficiency one with a condensate trap? On those the trap and drain line are supposed to be flushed annually, and if a tech skips that on a high-efficiency install I would take that as a pretty clear sign of a rushed job.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required