Hoping someone can ID a part for me. There's a disc-shaped component sitting at the bottom of the electric furnace in my mobile home, and I have no idea what it's actually called. It's got insulated wires coming off it, red ones and orange ones, and they plug onto the terminals with those flat spade connectors. I tried searching around online but without a name for the thing I'm just guessing at search terms. One thing that's got me a bit concerned is the condition of it. The part itself and the metal around it are pretty heavily rusted, there's corrosion on there, a good bit of dust, and honestly it kind of looks like there's been some moisture buildup in that area too. Not sure if that's normal for a furnace down low or if it's a sign of a bigger problem. So anyway, does anyone know what this part would be called? Figured if I can get the proper name I can at least look up what it does and whether the shape it's in is anything to worry about. Thanks in advance.
What is this round part at the bottom of a mobile home electric furnace called?
Nov 21, 2026
Last reply: 13 hours ago
3 Replies
Follow replies to this discussion?
First reply
What you're describing sounds like a sequencer, sometimes called a T.O.D. switch. That's the name you want for searching. The way it works is it staggers the electric heat strips so they don't all kick on at the same time. If everything came on at once you'd get a huge amp draw…
Read the full replyInformation here may be outdated?
What you're describing sounds like a sequencer, sometimes called a T.O.D. switch. That's the name you want for searching. The way it works is it staggers the electric heat strips so they don't all kick on at the same time. If everything came on at once you'd get a huge amp draw all at once, so the sequencer brings the elements on in stages instead. The red and orange wires on the spade terminals are exactly what I'd expect to see on one, and the disc shape sitting low in the cabinet fits too. On older units it was just called a sequencer, so either term should get you results when you look it up. Now, the rust and moisture part. I wouldn't ignore that. Corrosion on the component and the metal around it, plus what looks like moisture buildup down at the bottom of the cabinet, is not really normal wear. A little dust down low is one thing, but heavy rust means water has been getting in there or condensing somehow, and that's not a condition you want to leave an electric furnace sitting in. Moisture and electrical parts inside a furnace cabinet don't mix well over time.
It might be worth figuring out where the water is coming from before you do anything else. Could be condensation, could be something external getting in, hard to say from here. But I'd get it looked at rather than just swapping the part and carrying on, because if the environment that rusted it is still there, a new one will end up the same way. So yeah, search for sequencer or T.O.D. switch and you should find plenty on what they do and how they're wired. And once you know the name, it's worth having someone with HVAC experience take a look at the rust situation, since that's honestly the bigger worry here.
That name still holds up, the one the other fella gave you. Back when I ordered parts over the counter, the counter man knew it as a T.O.D. switch and that's what went on the ticket. Sequencer showed up in the newer books, but either one gets you the right bin. The way you describe it sitting low with those colored leads on spade lugs matches what I remember of them. As for the rust and damp, I'd be asking myself what's running near that furnace. In a mobile home there's usually a washer, water heater or plumbing not far off, and any of those leaking can wick moisture to the low corner of a cabinet. Have a look at what's on the other side of that wall before you order anything.
For me the name was always the sticking point too. I spent ages calling that same disc thing a 'relay' and a 'thermostat' and getting nowhere with parts searches, so hearing sequencer confirmed twice here is the bit I'd run with. One name, one search, whole world opens up. But the bit that stuck with me reading this was the moisture. Mine lives in a dry spot and still collected enough dust down low to make me nervous, so rust plus posible water on an electrical part whould have me moving fast. Was your furnace sitting anywhere damp, like low to the ground where wet air could reach it?
Join the Discussion
Have something to add? Share your thoughts — no account required.
Didn't find your answer?
Ask the community — no account required