What should I fill these joint gaps with after pressure washing?

Oct 27, 2026 Last reply: 2 weeks ago 6 Replies
Saved reading

First reply

pike_maker

Did the same cleanup on my place a couple years back and here's what worked. You're right that those gaps are functional. Concrete slabs expand and contract with the seasons and the joints give them somewhere to move. Filling them solid with mortar or cement is how you end up…

Read the full reply

Spent the whole weekend pressure washing my driveway for the first time in years and it looks great, except now the gaps between the slabs are completely empty. They were packed with dirt, pebbles and a bunch of weeds before, so I dug and washed all that out. Now I'm second guessing wheather I shold have left well enough alone.



I always assumed those gaps were there on purpose for the concrete to move, so filling them with cement or mortar seems wrong. But leaving them open just means the weeds come right back by July, right? My neighbor did the foam backer rod thing with sealant on top a couple summers ago and it all peeled out within a year, wich kind of scared me off that route.



Someone mentioned polymeric sand to me once but I'm not sure if that's meant for paver joints only or if it works in a poured driveway too. Do I need to buy an actual joint sealant, and if so does it go over sand or straight into the clean gap? Also wondering how deep I should fill it, since the gaps look like they go down a good couple inches. Any advice from people who've dealt with this woud be great.


Did the same cleanup on my place a couple years back and here's what worked. You're right that those gaps are functional. Concrete slabs expand and contract with the seasons and the joints give them somewhere to move. Filling them solid with mortar or cement is how you end up with cracks running through the slabs themselves, so don't do that. Polymeric sand is really a paver joint product, it's meant for the thin gaps between pavers sitting on a compacted base, not for a poured slab's control joints. It'll crack and wash out of a driveway gap that wide.

The right setup is foam backer rod with a self-leveling concrete joint sealant over it. Your neighbor's probaly failed for one of a few common reasons. If the rod isn't stuffed in snug it sits loose and the sealant has nothing pressing it against the sides. Or the gap wasn't fully dry and dust-free when they caulked, so the sealant never bonded. Or they used a cheap paintable caulk instead of an actual concrete sealant, which just isn't flexible enough and tears loose the first hot week.

My process was pretty simple. Blow the dust out of the clean gaps and let them dry a full day, longer if it's been humid. Pick a backer rod diameter bigger than the gap so it compresses when you push it in. I used a flathead screwdriver to seat it down into the gap. Leave room on top for the sealant. Rule of thumb is the sealant layer should end up about as deep as the gap is wide, so on a half inch gap leave roughly half an inch of space above the rod. Then run a bead of self-leveling concrete sealant and it spreads itself flat. Keep tires off it for a day or two while it cures.

Done right it stays flexible with the slab and lasts years, and weeds can't seed in there anymore.

Agree with the backer rod and sealant plan, but timing matters too. I did my dad's driveway last October when the slab had been sitting around 60 degrees all day, and two years later it's still stuck tight. If you seal on a blazing hot afternoon the concrete is expanded, then when winter comes the joint opens wider and pulls on the cured bead. Pick a mild day, morning is fine, so the gap is closer to its average width when you fill it.

One thing I'd check before buying anything is whether every gap is actually a sawn joint, becuase on my driveway one of them turned out to be a real crack running through the middle of a slab, not a control joint at all, and it was wider at the top than the bottom. A self-leveling bead will follow a V-shaped crack down forever and you'll burn through tubes. I ground the top of mine into a clean square channel first so the rod and sealant had parallel walls to sit against, and it's held up fine since.

One tip from my own mistakes, don't pile the sealant up proud of the slab. I did that on my first go because it looked better wet, then the shovel caught it every winter and my truck tires peeled the edges off. Keep it a hair below the surface and it'll survive way longer. Also if the rod feels loose in any spots, you can twist a thinner piece in behind it instead of pulling the whole run out.

This is all super helpful, thanks. I washed my dad's driveway last summer and chickened out on the gaps, so the weeds won again. One thing I'm fuzzy on is the foam rope stuff, does that come in one standard size or do I have to measure the gaps first? Mine vary a bit from one end of the driveway to the other, some look skinnier than others. Also does the tube go in a regular caulking gun or is that one of the big sausage type guns?

Update: did the backer rod and sealant job this weekend and it went way easier than I expected. Waited for a cool morning like someone suggested so the slabs weren't expanded. Kept the bead just under the surface like you all warned, my shoveling days of catching it are hopefully over. Also found one gap that turned out to be a crack, so I left that one alone for now.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required