Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

NuCRAFT ROUTER TABLE

Looking for a good used NuCraft Router table. Clean. NuCraft leg set desirable. Insert not required. Together about 90...
10 comments posted 9yrs
posted by coyote.moon
10 comments posted 9yrs posted by coyote.moon

favorite cat's paw nail pullers?

Yesterday, while deconstructing a small fence for the pickets (12" tongue g roove redwood), I couldn't locate my cat's...
7 comments posted 9yrs
posted by patm31751
7 comments posted 9yrs posted by patm31751

Pawn Shop Tool Score: Router & ROS

I bought a Woodpecker router table insert for my PC 690 router and built a router table extension for my table saw. I d...
39 comments posted 9yrs
posted by teamarrows
39 comments posted 9yrs posted by teamarrows

GE Silicone II failure

I just checked the seal between polycarbonate and wood on a frame, and the GE Silicone II I put on there is peeling off...
5 comments posted 9yrs
posted by michaeldwilson2
5 comments posted 9yrs posted by michaeldwilson2

Why do I keep doing it?

Years ago, I made a track saw. 'Twas a torsion box with some slick rails screwed to the side, that engaged a vertical r...
4 comments posted 9yrs
posted by whit3rd
4 comments posted 9yrs posted by whit3rd

New circular saw

I bought a Black and Decker 7 1/4" circular saw a few months ago and loved it. Last Friday I was breaking down some 2"...
35 comments posted 9yrs
posted by dangbert
35 comments posted 9yrs posted by dangbert

Builiding a shelf? Check out the Sagulator!

Kind of fun, although far too many choices of materials to choose from. 20 species of pine, 17 species of oak, etc. Doe...
8 comments posted 9yrs
posted by teamarrows
8 comments posted 9yrs posted by teamarrows

Hammer drills - corded

I need to buy a hammer drill to fasten a ledger board to a foundation for a deck. What do you guys like in hammer drills...
17 comments posted 9yrs
posted by Tom-NOSPAM-
17 comments posted 9yrs posted by Tom-NOSPAM-

How to Quickly Seal Hardboard

I recently purchased a latex mattress and platform bed frame. The wire grid was spaced much wider than recommended for...
5 comments posted 9yrs
posted by william
5 comments posted 9yrs posted by william

What To Look For In A Router Table Insert?

I'm thinking about building a router table extension for my table saw. I don't have room for a free-standing table and...
3 comments posted 9yrs
posted by teamarrows
3 comments posted 9yrs posted by teamarrows

Repair/reinforcement of double pedestal desk

I would like to repair and reinforce a 1930's Lincoln double pedestal office desk to use as a base for a metalworking l...
29 comments posted 9yrs
posted by bp
29 comments posted 9yrs posted by bp

Anyone recognize this latch?

Lav door latch (see link below) for our motorhome fails to catch the strike plate. Tried to disassemble only to discove...
4 comments posted 9yrs
posted by lawrence.r.tarnoff
4 comments posted 9yrs posted by lawrence.r.tarnoff

No Woodcraft in Tulsa for a while

The local Woodcraft store here in Tulsa is down for a while. We had an unexpected EF2 tornado early yesterday morning a...
15 comments posted 9yrs
posted by billnews2
15 comments posted 9yrs posted by billnews2

Anybody use a Roomba in the workshop?

Any of you guys use a Roomba (or other robot vacuum cleaner) to keep your shop floor clean? Just wondering if it works.....
64 comments posted 9yrs
posted by doug_at_milmac_dot_com
64 comments posted 9yrs posted by doug_at_milmac_dot_com

Table saw safety

Self explanatory but you have to feel bad for the guy. ouch! http://imgur.com/gallery/vaVwN
0 comments posted 9yrs
posted by esp
0 comments posted 9yrs posted by esp