Woodworking Forum

  1. Home
  2. Woodworking Forum
51626 Threads Posts
to

Worth reading in Woodworking Forum

old motor

Some of you will remember that I acquired an old (1948) Delta/Rockwell table saw and am restoring it. Well, I've got th...
8 comments posted 17yrs
posted by lblanch
8 comments posted 17yrs posted by lblanch

Shellac.net

Does anyone know if shellac.net is really up and running? Reason I ask is that a few years ago that site was inactive ev...
35 comments posted 17yrs
posted by fphowell
35 comments posted 17yrs posted by fphowell

FS: Grizzly G1035 Shaper Mesa, AZ

Good condition, with mobile base, 110V AC 1-1/2hp shaper, comes with 1/2", 3/4" and Router bit spindles. optional cast...
0 comments posted 17yrs
posted by escarcega
0 comments posted 17yrs posted by escarcega

Finishing cherry

I am building a small project out of cherry that will be in a kitchen and hence around water. Bob Flexner's book recomm...
10 comments posted 17yrs
posted by REMOVE-dicksnyder
10 comments posted 17yrs posted by REMOVE-dicksnyder

New Material for Mantels

Hey everyone I just wanted to introduce myself and say I am excited to say that Our business has created a New Propriet...
1 comments posted 17yrs
posted by leperrine
1 comments posted 17yrs posted by leperrine

Spread the wealth???

You cannot help men permanently by doing for them what they could and should do for themselves. Abraham Lincoln cm
95 comments posted 17yrs
posted by notcanadian
95 comments posted 17yrs posted by notcanadian

Penetrating Mixwax Stain

I used a Minwax Red Oak stain on some oak and it didn't turn out red enough. Attempts to stain over that with Red Mahag...
4 comments posted 17yrs
posted by geoff"at"
4 comments posted 17yrs posted by geoff"at"

Problem using Akeda DT jig

I purchased and Akeda jig a few months ago (lots of raves on the new group). I have begun using it to build a bunch of...
15 comments posted 17yrs
posted by l-lopez
15 comments posted 17yrs posted by l-lopez

6yo teaches drill press safety!

http://au.youtube.com/watch?v=Ml9IAcJT-jY
1 comments posted 17yrs
posted by abracadabra
1 comments posted 17yrs posted by abracadabra

OT: Phone Calls

I will really be glad when this election is over. I must be getting 25 phone calls a day from autodialers with recorded...
0 comments posted 17yrs
posted by lampaddadotherelighter
0 comments posted 17yrs posted by lampaddadotherelighter

OT: Too crazy not to share. Stunt Pilot.

Many of you have probably already seen this.... just nuts, I tell ya, just nuts. http://www.youtube.com/watch?v=XRCbkBfd...
7 comments posted 17yrs
posted by Counterfitter
7 comments posted 17yrs posted by Counterfitter

Question about Hand Saws

There's your typical North American hand saw such as a Disston that usually cuts on the push stroke and there's your ty...
30 comments posted 17yrs
posted by upscale
30 comments posted 17yrs posted by upscale

ACME Catalog Finally Out

For those of you who are uninformed, ACME is a leading manufacturer of goods and their deliever service is unsurpassed....
6 comments posted 17yrs
posted by Jakofalltrades
6 comments posted 17yrs posted by Jakofalltrades

O/T: Snopes

I often see references to www.Snopes in the Wreck. I was under the impression that it was kind of investigative legal o...
37 comments posted 17yrs
posted by whateveryoulike
37 comments posted 17yrs posted by whateveryoulike

RE: Lew's Country Ribs

With cold weather just around the corner for much of the country, the following may be of interest. Yes, it was posted...
12 comments posted 17yrs
posted by lewhodgett
12 comments posted 17yrs posted by lewhodgett