Woodworking Forum

51629 Threads Posts
to

Why Joiners shouldn't use nails

I'll bet this guy will start using less hardware in his joinery. http://www.thisisnorthscotland.co.uk/displayNode.jsp?no...
16 comments posted 22yrs
posted by waterrockets
16 comments posted 22yrs posted by waterrockets

Re: Sandplate from Sandvik

> Onderstaand bericht was in het engels omdat ik het gecrossposted heb op > andere NGs. > Het is eigenlijk bedoeld voor...
0 comments posted 22yrs
posted by adelcoGENE
0 comments posted 22yrs posted by adelcoGENE

Incra Miter Gauge question

The Incra Miter Gauge 2000 has an unusual screw at the pivot joining the top and bottom plates to the slider. It has a...
2 comments posted 22yrs
posted by losonsky
2 comments posted 22yrs posted by losonsky

question on glueing veneer

Hi, I haven't done any project with veneer before and just about to start one. From reading this newsgroup, I think the...
1 comments posted 22yrs
posted by thai_tx
1 comments posted 22yrs posted by thai_tx

FS - Old Table Saw

I thought I would try here first before an ad on eBay. I have an old Craftsman King-Seeley table saw I would like to fi...
11 comments posted 22yrs
posted by brian
11 comments posted 22yrs posted by brian

Last time I go cheap

Danged Penn state pipe clamps. Wilst in the middle of a glue up, ahh nevermind. Never again. Crap. SH
2 comments posted 22yrs
posted by I'm
2 comments posted 22yrs posted by I'm

Sun and sun beams

The piece I'm making is a sun with radiating sunbeams. The sun and beams are a glue up of separate pieces of a variety...
5 comments posted 22yrs
posted by ochsman
5 comments posted 22yrs posted by ochsman

Finshing Spanish Cedar door

I just picked up the gorgeous custom Spanish Cedar entry door for our under-construction new home. I'm about to start w...
3 comments posted 22yrs
posted by sflynn
3 comments posted 22yrs posted by sflynn

OT - Door Weatherstripping

Not exactly related to WW, but I have exterior doors with a flat copper weatherstripping band that is about 1/25" wide....
5 comments posted 22yrs
posted by jc_va
5 comments posted 22yrs posted by jc_va

Drill Press... full size or desk model

There are times I have really needed a drill press but have compromised and used my hand held. I would really like to k...
17 comments posted 22yrs
posted by babymakes4
17 comments posted 22yrs posted by babymakes4

Any experience with the Ryobi DP101?

I am looking for a relatively basic drill press to enable me to drill straight holes in wood and to use as a mortising...
5 comments posted 22yrs
posted by anonymous
5 comments posted 22yrs posted by anonymous

E-mail from SawStop (long)

I received this e-mail from the SawStop folks this AM. (for anyone that cares). September 2004 We have recently receive...
19 comments posted 22yrs
posted by mdg0911
19 comments posted 22yrs posted by mdg0911

COVERED BRIDGE

http://summerville-novascotia.com/CoveredBridges/Plans.html JOAT If you believe you can tell me what to do, I believe I...
1 comments posted 22yrs
posted by Jakofalltrades
1 comments posted 22yrs posted by Jakofalltrades

WWJ (current) clamp question

I bought the issue, I love those huge clamps being used, with blue paint on the jaws, what is the name of them as a type...
4 comments posted 22yrs
posted by ahem
4 comments posted 22yrs posted by ahem