Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Re: Undergrad chemistry college choice

>I want to study chemistry at a good college or university. I live in >the US, but I will consider schools abroad. What...
2 comments posted 21yrs
posted by lparker
2 comments posted 21yrs posted by lparker

Decent but cheap bench drill press?

My first post to this group--thanks for all the help available. I'm looking for a benchtop drill press that wouldn't be...
20 comments posted 21yrs
posted by acomarow
20 comments posted 21yrs posted by acomarow

Re: Is woodturning considered woodworking?

> Is woodturning considered woodworking? Or are they different crafts? All the people I know, other than turners, figur...
15 comments posted 21yrs
posted by dave
15 comments posted 21yrs posted by dave

Shop cabs - level or follow floor slope ?

I'm redoing the shop in my garage and am wondering if I should have the base cabs level or have them follow the slope o...
9 comments posted 21yrs
posted by Folk
9 comments posted 21yrs posted by Folk

Re: Best infant formula for newborns

" snipped-for-privacy@balderstone.ca" wrote in message news: snipped-for-privacy@z14g2000cwz.googlegroups.com... > Hi....
8 comments posted 21yrs
posted by sburke9368
8 comments posted 21yrs posted by sburke9368

Handcut Dovetails

Alright, So I am now teaching myself how to handcut dovetails. One problem though, I am having a hard time cleaning up...
11 comments posted 21yrs
posted by megold.andrew
11 comments posted 21yrs posted by megold.andrew

how to get smooth surface

I am painting a Aluminum surface with a brush and roller, With a brush, I get little lines from brush, with the roller,...
12 comments posted 21yrs
posted by andrewxiang
12 comments posted 21yrs posted by andrewxiang

Black pipe or galvanized for air?

For compressed air, is galvanized or black pipe better? Any reasons not to use galvanized pipe? Are 1/4" NPT black pipe...
8 comments posted 21yrs
posted by belfert
8 comments posted 21yrs posted by belfert

Sizing pilot holes for hardwood

Hi. Dumb question probably, but I have to screw into some hard maple and was never sure about how to match up a pilot h...
4 comments posted 21yrs
posted by dwhite110
4 comments posted 21yrs posted by dwhite110

Preventing table leaf warping

I have an antique dining room table, quarter cut oak, 6 leafs were thrown out years ago. I would like to make some new...
0 comments posted 21yrs
posted by denada.rh
0 comments posted 21yrs posted by denada.rh

Stanley 110

Does anyone know how to close down the mouth of these little jewels? The mouth is rather wide. The plane makes very nic...
12 comments posted 21yrs
posted by ahem
12 comments posted 21yrs posted by ahem

Need Fine Woodworking article from Jan/Feb 2002 issue

I'm hoping someone can help me out with a copy of an article from the Jan/Feb 2002 Fine Woodworking magazine. It is an...
8 comments posted 21yrs
posted by dalemartindesigns
8 comments posted 21yrs posted by dalemartindesigns

What am I doing wrong with Google Groups

Seems like it used to be when I read posting on Google, exited and came back later it showed the number of posts since...
4 comments posted 21yrs
posted by mike72903
4 comments posted 21yrs posted by mike72903

Varnishing Quilted Maple?

I bought some quilted maple and have sanded (to 220) and varnished a scrappy piece just to see what it looks like. Ther...
8 comments posted 21yrs
posted by toller
8 comments posted 21yrs posted by toller

9.6, 12 or 14.4

The batteries for my 9.6V DeWalt cordless screwdriver/drill have just about had it. Should I buy two new batteries for...
8 comments posted 21yrs
posted by NunyaBiznas
8 comments posted 21yrs posted by NunyaBiznas