Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Setting Up Woodshop Help

I am setting up my woodworking shop and need advice on the tools I will place in the shop, specifically I need advice a...
19 comments posted 21yrs
posted by nature41
19 comments posted 21yrs posted by nature41

Ranking Powertool Makers

Hello Everyone, I'm a newbie to this NG and Woodworking. I am wondering if you could rank the following tool makers fro...
38 comments posted 21yrs
posted by bloke
38 comments posted 21yrs posted by bloke

American Fabric Filters (in Florida)

Does anybody know the current status of these guys ??? http://www.americanfabricfilter.com/I spoke to them before the h...
9 comments posted 21yrs
posted by MBOCEANSIDE
9 comments posted 21yrs posted by MBOCEANSIDE

INSPIRATION - Duck Silhouette

http://www.rjgantiques.com/decoys/11781.htm This one is dedicated to Bob. I'm a bit confused about it, but it was somet...
4 comments posted 21yrs
posted by Jakofalltrades
4 comments posted 21yrs posted by Jakofalltrades

Mortise jig

A couple of years ago, I built a jib, based roughly on the Leigh Frame Mortise and Tenon jig. I believe I based my work...
3 comments posted 21yrs
posted by randy.hinton
3 comments posted 21yrs posted by randy.hinton

Estwing Weight Forward Hammer

Iv'e been thinking of buying one of these hammers for quite a while bu i don't know anyone who has used one before. Has...
6 comments posted 21yrs
posted by Scooby.1itjlm
6 comments posted 21yrs posted by Scooby.1itjlm

Pet ramp plans?

I'm looking to build a pet ramp for aging Golden. Anyone have a plan for a vehicle pet ramp?
14 comments posted 21yrs
posted by dolphans1
14 comments posted 21yrs posted by dolphans1

Anyone using an Excalibur SLT60 on a Unisaw?

I'm wondering about the removal of the left side table wing interfering with normal ripping operations. Also if you cut...
2 comments posted 21yrs
posted by Knothead
2 comments posted 21yrs posted by Knothead

"soft-close" drawer glides

Yes I am in the design process for kitchen cabinets. I saw this with the paragraph quoted... http://www.austinhomeandli...
6 comments posted 21yrs
posted by gbeshers_nospam
6 comments posted 21yrs posted by gbeshers_nospam

how to paint a small Aluminum box?

I have a small Aluminum box (4x4x8") with electronics inside that I want to give it a nice finish. I tried with water b...
17 comments posted 21yrs
posted by andrewxiang
17 comments posted 21yrs posted by andrewxiang

Bandsaw followup

I've checked out the 14" Rigid, Powermatic, Delta BS but what do you think of those 2 ? (in Canada) http://www.general.c...
8 comments posted 21yrs
posted by jackeric
8 comments posted 21yrs posted by jackeric

PAY - ICE BOAT

http://www.cherrywoodmedia.com/Plans/IceBoat/iceboat.htmJOATSuccess is getting what you want. Happiness is wanting what...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

Grizzly G0566 Bandsaw 21"

Does anyone have this saw and have it in use? Would like to hear what you think of it. Thanks, Larry
0 comments posted 21yrs
posted by lbarnes
0 comments posted 21yrs posted by lbarnes

ICE BOAT

http://www.inquiry.net/outdoor/winter/gear/sleds/ice_boat.htmJOAT Success is getting what you want. Happiness is wanting...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

PAY - WOODEN SNOW SLED PLANS

http://www.projectsandhobbies.com/snowsled.htm Kinda neat actually. JOAT Success is getting what you want. Happiness is...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades