Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Chatter at end of cut DeWalt Planner DW733.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I am getting some chatter on the left side at the end of a cut. Depth of...
5 comments posted 21yrs
posted by wkc
5 comments posted 21yrs posted by wkc

Gloat - I think

Just returned from an auction with a Delta/Rockwell 33-990 RAS in really good shape (no rust, etc). Paid $50.00. The re...
6 comments posted 21yrs
posted by dontknow
6 comments posted 21yrs posted by dontknow

Handrail bracket

I need to install a handrail going into the basement in a split entry. The top part of the rail mounts to a 2x4 wall an...
0 comments posted 21yrs
posted by wincon
0 comments posted 21yrs posted by wincon

Handrail bracket

I need to install a handrail going into the basement in a split entry. The top part of the rail mounts to a 2x4 wall an...
0 comments posted 21yrs
posted by wincon
0 comments posted 21yrs posted by wincon

Handrail bracket

I need to install a handrail going into the basement in a split entry. The top part of the rail mounts to a 2x4 wall an...
2 comments posted 21yrs
posted by wincon
2 comments posted 21yrs posted by wincon

For Sale: 313 Board Feet Cypress lumber

Approximately 313 Board Feet rough sawn Cypress. Air dried & stored inside. Paid $1.50 / board ft. plus shipping (aroun...
0 comments posted 21yrs
posted by tagresta
0 comments posted 21yrs posted by tagresta

How do you route the edge of a 9" wooded disk

Afternoon all, I need to round over the edge of a piece of 3/4" ROak with a 9" dia. Is there an easy and safe way to do...
11 comments posted 21yrs
posted by ronaldjangel
11 comments posted 21yrs posted by ronaldjangel

TS belt size?

I'm upgrading my Delta contractor saw drive belt to a power twist. To size it properly I need to know the original belt...
3 comments posted 21yrs
posted by dpenner
3 comments posted 21yrs posted by dpenner

MLCS MARVEL 60 router

Anyone have any experience with the MLCS MARVEL 60 3 HP Variable Speed Plunge Router? this is the most economical 3 hp r...
11 comments posted 21yrs
posted by dshackleford
11 comments posted 21yrs posted by dshackleford

Slide-out Shelf

I need to come up with a method to occasionally extend the depth of a counter top by about 20". The extension will have...
10 comments posted 21yrs
posted by rkola
10 comments posted 21yrs posted by rkola

laminate floorings

Need any and all information about laminate floor installation,what to look for and what to stay away from,I would like...
5 comments posted 21yrs
posted by acr
5 comments posted 21yrs posted by acr

Wood Movement: Case hardening vs moisture change

I am milling some face frame and cope & stick door material from poplar. I jointed a face flat, planed parallel, and jo...
0 comments posted 21yrs
posted by JDWHATSOBVIOUSCaff
0 comments posted 21yrs posted by JDWHATSOBVIOUSCaff

Lifting a cabinet saw

I have a new Delta 3HP 50" Biese cabinet saw I bought from Amazon. I have had it (on the palate) on my mobile flatbed c...
6 comments posted 21yrs
posted by snpollack
6 comments posted 21yrs posted by snpollack

The SECRET Society, again... and yes, it's a gloat!

Folks - OK, apparently all is forgiven - I just got my PRE-APPROVED HCA MEMBERSHIP MONOGRAPH in yesterday's mail. Y'kno...
9 comments posted 21yrs
posted by johnmoorhead
9 comments posted 21yrs posted by johnmoorhead