Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

compressor and nailer recommendations

Can anyone give me some recommendations on an air compressor and nail guns. I will be using them for cabinet work. Thank...
8 comments posted 21yrs
posted by angharad
8 comments posted 21yrs posted by angharad

Slicking Up the TS Table (and a bit of gloat)

Last week I noticed in this group that "TAP" had some tools for sale in the Dallas area. Gave him a call, took a look,...
7 comments posted 21yrs
posted by xleanone
7 comments posted 21yrs posted by xleanone

Parts for OLD craftsman table saw

I've been given an early 1950s Craftsman/Emerson Electric Co. Model# 113 27520 table saw. It runs, but the cranks are b...
7 comments posted 21yrs
posted by shadux
7 comments posted 21yrs posted by shadux

Just Back from Divin' In the Chicago ARea

I picked up a rusty, broken Stanley #78 and two other thing-ga-majigs plus a pile of old horseshoes and other stuff. Ma...
7 comments posted 21yrs
posted by llhote
7 comments posted 21yrs posted by llhote

Is this Delta 34-740c worth keeping?

I got a free Delta 34-740C tablesaw (gloat, or maybe not). It had sat outside over a southern Ontario Canada winter. Th...
8 comments posted 21yrs
posted by john.antoszek
8 comments posted 21yrs posted by john.antoszek

Wouldn't it be nice..

if OP's interacted with the responders to their threads, within a reasonable time frame, so that those who took the tim...
58 comments posted 21yrs
posted by David
58 comments posted 21yrs posted by David

sourcing 200ft² of Jatoba

Hello, I am looking for 200 sf² of Jatoba 4/4, 5" or wider boards. I can find the thing for $5 / bf localy in boise, do...
1 comments posted 21yrs
posted by cyrille
1 comments posted 21yrs posted by cyrille

Woodworking show - SF Bay area Report

Went to the Sacramento show this weekend. Noticed that there weren't a lot of people in the hall. After walking around...
2 comments posted 21yrs
posted by mjwallace
2 comments posted 21yrs posted by mjwallace

pen turning with snakewood

I'be acquired some snakewood I was going to use for pen blanks, but I've been told that this wood is impossible to use...
1 comments posted 21yrs
posted by e.lowenstein
1 comments posted 21yrs posted by e.lowenstein

Best tool to trim top of pine cabinet?

I've got to trim a quarter inch off of the top of a pine cabinet to make room for a new refrigirator. The cabinet sits...
15 comments posted 21yrs
posted by nothanks
15 comments posted 21yrs posted by nothanks

Incra Rocks!

Rec'd an Incra fence for my table saw/router last week and I must say WOW! Honestly, I had some reservations about payi...
1 comments posted 21yrs
posted by daryl1138
1 comments posted 21yrs posted by daryl1138

Makita plate joiner

Any comments on this. I'm looking at a new one and was told tis one received Popular Woodworking's Editor's Choice.
4 comments posted 21yrs
posted by bubba
4 comments posted 21yrs posted by bubba

Re: Finishing a Pine Table Top

> I have considered taking it to a local wood shop and getting it planed > down. Would that be expensive? > > Would it...
5 comments posted 21yrs
posted by mp
5 comments posted 21yrs posted by mp

Profile Problem

I needed some bar arm rail of a bar that I am making and saw a profile similar to the one shown below at a custom shop....
3 comments posted 21yrs
posted by JGS77Stamp
3 comments posted 21yrs posted by JGS77Stamp