Woodworking Forum

Saw Blade Test

Here is some interesting information. A test of several 7.25" circular saw blades. Ripping a 2x4, again with 10 framing...

6 comments posted 4yrs

posted by lcb11211

6 comments posted 4yrs posted by lcb11211

Adjusting table height

Hello my table on my 2040 wont go up and down even after much pressure and we 40 on all posts and gears is there some hi...

1 comments posted 4yrs

posted by george

1 comments posted 4yrs posted by george

Miss Cleveland Builds a Rocket (On-Topic)

Note that she's a rather extreme Nahmite (by extreme I mean she doesn't just use power tools, she uses lasers). Also, sh...

0 comments posted 4yrs

posted by jclarke.873638

0 comments posted 4yrs posted by jclarke.873638

Cutting Lumber Core Plywood On A Table Saw

I have a few scraps of 3/16" lumber core plywood that I scarfed from a friend's woodbin many years ago. I've never used...

41 comments posted 4yrs

posted by teamarrows

41 comments posted 4yrs posted by teamarrows

craftsman bandsaw rip fence assessory #9-23433

I have not been able to find the rip fence for this very good bandsaw

1 comments posted 5yrs

posted by John

1 comments posted 5yrs posted by John

#63607 Craftsman motor just buzzes

#63607 motor for Craftsman RAS #113.19770 buzzes, and jerks as if trying to start turning when i turn it on power. But...

8 comments posted 5yrs

posted by Jeffrey

8 comments posted 5yrs posted by Jeffrey

TR-8 Router collett chuck (hitachi European model part number: 971857z)

Hi All. A bit of a long shot...has anyone out there got either a spare or know of access to a replacement collett and c...

2 comments posted 5yrs

posted by Mark

2 comments posted 5yrs posted by Mark

Rockwell 4676 router manual? I need to replace the collet to a 1/2" collet and would like to know what size would the replacement be or if I can use a different brand collet??

Where can I get a Rockwell 4676 router manual? I need to replace the collet to a 1/2" collet and would like to know what...

0 comments posted 5yrs

posted by martyb365

0 comments posted 5yrs posted by martyb365

Oneida Super Dust Deputy XL 6”

Wondering if anyone has installed this? Is it an efficient cyclone when paired with a high merv cartridge filter? Planni...

25 comments posted 5yrs

posted by Aaron G

25 comments posted 5yrs posted by Aaron G

Festool Cord/hose clips

For anyone with a Festool dust collector, these hose clips work very well. I've noticed a lot of people are putting thei...

2 comments posted 5yrs

posted by krw

2 comments posted 5yrs posted by krw

The Platforms For My Vehicle Are Complete - (Carpeted 2 x 4's)

Over the past 4 generations of the Honda Odyssey, the floor has been getting more and more bumpy and unlevel. It gets h...

157 comments posted 5yrs

posted by teamarrows

157 comments posted 5yrs posted by teamarrows

Ping Sonny: How do you carpet a 2 x 4?

I need to wrap carpet around the end of a 2 x 4 that is attached to a sheet of plywood. Take a look at the images below...

39 comments posted 5yrs

posted by teamarrows

39 comments posted 5yrs posted by teamarrows

To Drby Dad

So if you felt I called you a troll, I apologize.

90 comments posted 5yrs

posted by markrm618

90 comments posted 5yrs posted by markrm618

Plywood: Is MDO Always Cheaper Than Sheathing?

I just bought a sheet of 1/2" Douglas Fir MDO Plywood at Lowes. Actual thickness: 0.484. The entire stack (50 sheets?)...

13 comments posted 5yrs

posted by teamarrows

13 comments posted 5yrs posted by teamarrows

Rebuilding Outdoor Bench - Wood Suggestions?

It's time to rebuild the bench I inherited from my Grandparents. It was around when I was a kid, so it's gotta be at le...

16 comments posted 5yrs

posted by teamarrows

16 comments posted 5yrs posted by teamarrows