Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Do you like Chinese products?

Most power tools and accessories are made from China.their price is low,I don't know the products' quality??
23 comments posted 21yrs
posted by bobotang
23 comments posted 21yrs posted by bobotang

Sharpening question

I have an old router plane blade shaped rather like the following (except the bevel is about 30 degrees) | | /|\ | | |...
6 comments posted 21yrs
posted by gkraig
6 comments posted 21yrs posted by gkraig

TS Zero Clearance Insert Question

So I just recieved and installed my zero clearance insert from Grizzly for my 1023S. I've never used one of these inser...
12 comments posted 21yrs
posted by AggieSawDust
12 comments posted 21yrs posted by AggieSawDust

Q about rubbing alcohol & wood

Hey! I hope this is a good place to ask this Q. I just had a minor invasion of ants in and around my kitchen sink, and...
6 comments posted 21yrs
posted by ratj
6 comments posted 21yrs posted by ratj

PING Luigi

http://familycrafts.about.com/cs/wintercrafts/a/blicepalace.htm Just ran across this, and immediately thought of you. J...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

VACUUM PUMP

http://www.dream-models.com/eco/vacuumpump.html Hadn't seen this site before. Ran across it while going thru a batch of...
4 comments posted 21yrs
posted by Jakofalltrades
4 comments posted 21yrs posted by Jakofalltrades

Advice on bandsaws

Thanks to everyone for the router bit advice. I have another question. Since I have a good miter saw, and I want to do...
6 comments posted 21yrs
posted by "mywebaccts (at) PLUGcomcast.n
6 comments posted 21yrs posted by "mywebaccts (at) PLUGcomcast.n

extreme birdhouses and more.new member.pics

hi everyone my name is john . i am from cranbrook ont can. I am 40 yrs old and retired from custom home building. since...
1 comments posted 21yrs
posted by cranbrook2.1tuay2
1 comments posted 21yrs posted by cranbrook2.1tuay2

OT: Wood Fence Installation

Hi all, I enjoy reading your discussion group on a weekly basis. I was hoping you might be able to help this little old...
5 comments posted 21yrs
posted by MGPuttPutt
5 comments posted 21yrs posted by MGPuttPutt

moisture meter

Greetings! I have been looking for an inexpensive moisture meter...some of the name brand ones are out of my price rang...
4 comments posted 21yrs
posted by granite_skies
4 comments posted 21yrs posted by granite_skies

Router bits (yes .. again!) ... Looking for advice on brands

I did a quick review through the archive on router bit discussions, but my newsgroup service has many of them deleted a...
27 comments posted 21yrs
posted by "mywebaccts (at) PLUGcomcast.n
27 comments posted 21yrs posted by "mywebaccts (at) PLUGcomcast.n

Good table top, where to get?

I want to get a good looking table top (I already have a base), about 6 ft long and 3 feet wide. Any kind of wood is ok...
8 comments posted 21yrs
posted by jphkjkhkj
8 comments posted 21yrs posted by jphkjkhkj

Need help rewiring a DeWalt 7790 radial arm saw

Hello! I was lucky enough to get a DeWalt 7790 12" RAS from a pawnshop for $125. It was in great condition and runs wel...
1 comments posted 21yrs
posted by skipsizemore
1 comments posted 21yrs posted by skipsizemore

how to clean a table saw table (or band saw)?

Hello, I was wondering how you knowledgeable wood working veterans were cleaning your table or band saw tables (I imagi...
13 comments posted 21yrs
posted by cyrille
13 comments posted 21yrs posted by cyrille

Dust collector

Hello, I am new to woodworking. Was wondering whether a Shop Vac (6HP-16 gal) would be sufficient to collect dust from...
20 comments posted 21yrs
posted by mnagarkatti
20 comments posted 21yrs posted by mnagarkatti