Hoping someone can point me in the right direction here. My mini split is set to 70 but the air coming out feels like it's around 78, so basically it's not cooling at all. The lights first showed a PC code, I looked online and tried power cycling it like some people suggested. Here's the weird part. Cooling was working fine, then we got some rain and I switched it over to heater mode for 1 day. Next day I put it back on AC mode and boom, PC code again. This exact thing happened before and a tech came out and said it was just low on refrigerant. He topped it off and it cooled fine again, right up until I switched to heater mode once, and now it's back to blowing warm air. The other thing I noticed is the outdoor unit doesn't sound right. When it was cooling normally it was pretty loud, but now it just hums lightly, shuts off, and flashes the PC lights on the unit. Any ideas what would cause it to keep dying like this every time I touch the heat mode? Is there something I can check myself or is this another call to the tech?
Why does my mini split stop cooling after I run it in heater mode?
Nov 19, 2026
Last reply: 14 hours ago
3 Replies
Follow replies to this discussion?
First reply
That PC code is a pressure protection fault, not a message saying the unit needs more refrigerant. It means the low side pressure has dropped too far or the system is tripping a protection circuit, and adding refrigerant on top of that without finding out why the pressure isβ¦
Read the full replyInformation here may be outdated?
That PC code is a pressure protection fault, not a message saying the unit needs more refrigerant. It means the low side pressure has dropped too far or the system is tripping a protection circuit, and adding refrigerant on top of that without finding out why the pressure is low just masks the problem for a while.
And that's basically what happened here. The last tech topped it off, cooling came back, and then one day of heat mode killed it again. If the charge were simply low from a slow leak you'd expect it to fade gradually regardless of mode. The pattern you're describing, where it cools fine until you touch heat and then dies, points at something mode specific. One known cause is a kinked vapor line from the original install. In cooling mode the system can sometimes struggle through it, but switch to heating and the flow direction reverses, the restriction bites hard, pressures go wrong, and the PC code shows up. Worth having whoever comes out check the line set run for that.
The way the outdoor unit is behaving now is also telling. Humming lightly, shutting off, flashing the code instead of running loud like it used to, that fits a compressor under strain, a stuck or failing reversing valve, or a communication fault between the indoor and outdoor boards. All of those are things for a qualified tech to check, not something to guess at from the thermostat side. The big thing I'd push back on with the next service call is the top-off itself. Refrigerant doesn't get consumed, so if it's low there's a leak somewhere, likely at a flare coupling or in one of the coils. Mini splits hold a pretty small charge, so even a slow leak takes the unit out fast, and heat mode puts much higher pressure on the indoor side where a leak would dump charge quicker. So instead of asking for more refrigerant, ask them to leak test the system, check the reversing valve and compressor, and look at the line set. Paying for repeated top-offs with no leak repair is money down the drain.
The detail that stands out to me in how you put it is the actual discharge temperature, since a setpoint of 70 with air coming out around 78 means the indoor coil is barely doing anything rather than just falling a little short, which lines up with a protection circuit shutting things down instead of weak performance. One thing I'd want to know before the tech shows up is whether heat mode actually blew warm air that one day it ran, or whether it acted up immediately then too. If it heated normally and then failed on the switch back, that pattern matters for what the technician ends up checking.
Following this one closely because I have a mini split too and I swap it to heat every now and then in the shoulder seasons, so this thread is making me think twice about that. The reply about the flow direction reversing in heat mode makes sense to me, but I have to ask, is the reversing valve the actual part that flips that flow direction? Like is that its whole job? I always assumed the unit just changed the setpoint and the same parts kept doing the same thing. Sounds like the tech visit for you needs to cover a lot of ground, sorry you're dealing with it again.
Join the Discussion
Have something to add? Share your thoughts — no account required.
Didn't find your answer?
Ask the community — no account required