Warranty refused without an inspection - where do you stand on this?

Nov 22, 2026 Last reply: 5 hours ago 4 Replies
Saved reading

First reply

ArrowEcho668

I'd be annoyed too. When I had a split under warranty I expected someone to actually come out and look, and a refusal built on photos plus a figure you clearly said was a rough guess would have sent me to the retailer as well. Treating an estimate as a measurement is the part…

Read the full reply

Curious how others would read this situation. In June 2025 I bought three identical Hisense Fresh Master units, model QF25XW00W, from a retailer here in Italy. All three went in via qualified installers with proper invoices and F-Gas paperwork. Two heat fine, the third puts out noticeably weaker heat even when all three are set to 30 degrees under similar conditions. When I contacted Hisense I figured a technician would come and look at it. Instead it's been days of emails: photos, measurements, troubleshooting steps. I tried the sensor recalibration they suggested, no change. It's not a wrong reading on the display, the unit genuinely heats weaker than its two identical siblings. Then they picked at the installation. They said refrigerant pipes need a minimum of 3 metres, though I can't find that in the spec sheet. I'd thrown out roughly 1 metre as a rough guess, not a measurement, and they ran with that figure. They also flagged the clearance above the outdoor unit, wich honestly is very tight against the balcony ceiling and might need fixing, plus the nearby boiler. Fair enough on enforcing installation rules, but nobody ever came out to look, measure or diagnose anything. They refused the claim off photos and an internal review, and now want me to have an authorized installer review and correct the installation first. I've gone back to the retailer to use the legal conformity warranty instead. So, opinions? Is refusing service sight unseen normal practice, or shoud they have to inspect first? And does thier approach sound reasonable to anyone, or am I right to be annoyed?


I'd be annoyed too. When I had a split under warranty I expected someone to actually come out and look, and a refusal built on photos plus a figure you clearly said was a rough guess would have sent me to the retailer as well. Treating an estimate as a measurement is the part that gets me. A guess is not a diagnosis, and when two of three identical units behave on the same job it's hard to pin the third one on the pipework alone. The tight clearance over the outdoor unit and the boiler sitting close by are fair things for them to raise, but those are for a technician to check in person, not to settle from pictures. Chasing the legal conformity warranty through the seller looks like the right call to me, since that obligation sits with the retailer no matter what the manufacturer claims. Save every email, the recalibration attempt, the photos, all dated. If they eventually do send somebody out, the paper trail shows you cooperated fully before they said no. In my experience manufacturers count on people giving up after the first rejection, so don't give them that satisfaction.

Honestly, I read Hisense's side of this a bit differently. When I was fitting splits years back, warranty departments almost always triaged by photos and questions first, because alot of 'weak unit' calls turned out to be siting or installation problems rather than a fault they'd have to pay a technician to chase. The 3 metre minimum pipe run is a real requirement on plenty of these units, it lives in the installer manual even when the consumer spec sheet leaves it out, so them running with a number you gave them, rough as it was, is at least them working from something on paper rather than inventing a rule.

Where I think they've overstepped is going from triage straight to a flat refusal without anyone coming out, expecially since you admit the clearance above the outdoor unit is tight and might need correcting. That's a fixable site issue. A refusal should follow an inspection that confirms the installation is the cause, not replace the inspection entirely.

Even so, I'd say the route you've alredy taken is the stronger one regardless. The legal conformity warranty puts the burden on the seller, and the retailer can't shuffle you off to the manufacturer the way the manufacturer shuffled you off to an authorized installer. I'd let the Hisense email chain sit while the retailer works, and only pick it back up if you end up needing the paper trail.

Back when I started, the maker sent a man with a manifold and a thermometer and he stood there until he knew the answer. Photos were for the family album. What still holds up from your post is the paperwork side: proper invoices and F-Gas docs from qualified installers is exactly the sort of thing that used to end these arguments on the spot. Makes it stranger that nobody came out to check. One thing I'd want to know, did the retailer say how the legal conformity route works with three units, or only the weak one? That one detail might decide how much grief this costs you.

What stands out to me is the balcony ceiling bit. You already suspect that clearance is too tight, so having it corrected by an authorized installer before anything else might actually strengthen your case rather than weaken it. When I did my own install I obsessed over every clearance number because I'd read how quickly warranty departments lean on that stuff.

The part I'd push back on is them running with your rough pipe figure without ever measuring. If it matters that much to their decision, it matters enough to send someone out with a tape. One thing I'm curious about: when you went back to the retailer, did they talk about a repair, a replacement unit, or taking the whole thing back?

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required