Woodworking Forum

51629 Threads Posts
to

How to make small wedges?

I am in process of making a series of wedged tenon joints and for that purpose I need to have quite a many small wedges...
11 comments posted 22yrs
posted by noSpamOlivili
11 comments posted 22yrs posted by noSpamOlivili

"PL" brand contact cement - any good?

Seeking recommendations for a good water-based contact cement. I saw "PL" brand contact cement at Menard's this afterno...
0 comments posted 22yrs
posted by spambait
0 comments posted 22yrs posted by spambait

Porter Cable vs. Bostitch Finish Nailer Combo Kits

After manually installing baseboards in half my house and borrowing my neighbor's nail gun/compressor for another quate...
23 comments posted 22yrs
posted by witczak
23 comments posted 22yrs posted by witczak

Table Saw jig for angles in the 3rd dimension

I may want to cut some dados in the corners of some square stock, in other words at 45 degrees to the flat surface. I k...
1 comments posted 22yrs
posted by me7
1 comments posted 22yrs posted by me7

instructions for rotary surface planer

Hello, Picked up a Barrow #9-2289 rotary surface planer via Ebay for possible use in flattening glued up segmented.ring...
0 comments posted 22yrs
posted by feinerman
0 comments posted 22yrs posted by feinerman

Restore BS Blade Set

Now that I figured out why my Bandsaw wouldn't cut a curve. Is there an easy way to restore the set on the teeth so I d...
7 comments posted 22yrs
posted by marcus
7 comments posted 22yrs posted by marcus

Router choices

I was at my local Lowe's today looking at routers. The 2 that were most appealing to me were the Bosch 1617EVSPK and th...
3 comments posted 22yrs
posted by LTill
3 comments posted 22yrs posted by LTill

OT Electric motor from auction

Ok here is the story, I went to an auction and picked up some bargans. The one that has gotten my interest was a lot of...
2 comments posted 22yrs
posted by larryhab
2 comments posted 22yrs posted by larryhab

flipper door slides

i'm looking to make some panel doors for a cabinet that will contain stereo equipment, as swmbo has requested non-glass...
5 comments posted 22yrs
posted by charlie.spitzer
5 comments posted 22yrs posted by charlie.spitzer

Now does this make *any* sense?

Warnings on a can of Weldwood brand NONflammable contact cement: "Contains toluene ... Use in a well ventilated area. K...
27 comments posted 22yrs
posted by spambait
27 comments posted 22yrs posted by spambait

Heads Up on Woodcraft brand Router Bits

Woodcraft has 10 of their 1/2" shank carbide router bits on sale for September. $5.00 each for specific ones. The web s...
2 comments posted 22yrs
posted by removespamlcb11211
2 comments posted 22yrs posted by removespamlcb11211

I got another handyman club membership

You would think after they sent me to collections for not paying for books I sent back to them they wouldn't try to get...
6 comments posted 22yrs
posted by nospam
6 comments posted 22yrs posted by nospam

New Unisaw on the Way

Hey all, My new (and first) 3 HP Unisaw should be here by Thursday. I got the 50" commercial Bies. fence. I don't expec...
54 comments posted 22yrs
posted by azwood
54 comments posted 22yrs posted by azwood

Router bit suggestion?

Hello all, Trying to locate a cutter that will edge/slot in a single pass. I have found several T&G bits where the groo...
4 comments posted 22yrs
posted by no
4 comments posted 22yrs posted by no