Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

laying wide oak floor boards tips

Hi, I am going to be laying new oak floor boards that are 230 x 22mm thick and am not entirely sure of best method. It...
3 comments posted 21yrs
posted by tcastle
3 comments posted 21yrs posted by tcastle

HAPPY THANKSGIVING!

Hope all our carvers out there are doing a good job today. Happy Thanksgiving to all. Searcher1
11 comments posted 21yrs
posted by Unitedair2004
11 comments posted 21yrs posted by Unitedair2004

Introduction

OK, I have been lurking in here for about a month, and responded to a post about clipped head nails. Since I now feel c...
10 comments posted 21yrs
posted by robert27
10 comments posted 21yrs posted by robert27

How would You finish this? Novice needs advice

Confusion, then Indicision and now dispair. Stain, Dye, fill the grain, wipe on or spray. Too many options and not enou...
19 comments posted 21yrs
posted by jmweber987
19 comments posted 21yrs posted by jmweber987

router table setup

Hi, I'm getting ready -- finally -- to mount my router in the end of my table saw extension. I'm planning to use an aux...
6 comments posted 21yrs
posted by lmills01
6 comments posted 21yrs posted by lmills01

Router bit help needed

I bought the Lee Valley Drawer Lock bit (16J76.62) and I am perplexed about how to set it up properly for 3/4" fronts a...
2 comments posted 21yrs
posted by kulsetsiyi
2 comments posted 21yrs posted by kulsetsiyi

Will a Veritas Router Table Accept a Lift?

Anybody know if you can outfit the Veritas Router Table with a router lift? Seems most lifts require a rectangual basep...
4 comments posted 21yrs
posted by emptyshell
4 comments posted 21yrs posted by emptyshell

Groz Planes

OK. I know it ain't no Bailey, LN, etc., but probably not a Buck Bros, either. So does anyone have/know anything about...
10 comments posted 21yrs
posted by sysiphus
10 comments posted 21yrs posted by sysiphus

Radi plane sharpening

I have two of the wooden bodied radi-plane that need sharpening. I'm not sure how to do this -- I would have to grind a...
3 comments posted 21yrs
posted by mattheweash_no_spam
3 comments posted 21yrs posted by mattheweash_no_spam

Hood Wiping Wood Stain Test

Today I ran a stain sample test of 6 colors using the Hood Finishing Products "Wiping Wood Stain" on Cherry. IMO, the s...
6 comments posted 21yrs
posted by rumpty
6 comments posted 21yrs posted by rumpty

Leigh FMT/WoodRat/Multi-Router

I am looking at various mortise and tenon type machines. I am looking for something for a quasi-production environment....
6 comments posted 21yrs
posted by bwx100
6 comments posted 21yrs posted by bwx100

Tablesaw followup

Some of you may remember that I'm refurbishing an old Sears flex drive tablesaw. I got the rust off, adjusted the trunn...
5 comments posted 21yrs
posted by chuck94560
5 comments posted 21yrs posted by chuck94560

FS : Platinum Grey Formica Sheets

Great for shop projects as well as counter tops. 15 sheets available Raleigh, NC area $20.00 per sheet. Some may have s...
0 comments posted 21yrs
posted by me
0 comments posted 21yrs posted by me

Gloat, somewhat belated

My father got a good offer on his house, and he's cleaning out in preparation for moving to an apartment. So he's bring...
6 comments posted 21yrs
posted by Allen.Windhorn
6 comments posted 21yrs posted by Allen.Windhorn

Miter Saws

OK I have a question. What is the best miter saw made for critical angled cuts and square end trim cuts? Thanks George
8 comments posted 21yrs
posted by leapenjeep
8 comments posted 21yrs posted by leapenjeep