Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Re: Kitchen cabinet hardware

> Where can I get good quality kitchen cabinet hardware? Specifically I > need undermount invisible full extension draw...
2 comments posted 21yrs
posted by smeier-spamless
2 comments posted 21yrs posted by smeier-spamless

Re: wood selection question

Thanx for the input. Don't care for MDF so I've narrowed it down to two scenarios. If I confirm that I'm going to do a...
4 comments posted 21yrs
posted by vgbaron
4 comments posted 21yrs posted by vgbaron

Radial saw / Sliding saw

Why do you pull the saw into the work piece with a radial saw & push the saw into the work piece with a slidder?? Thanks...
14 comments posted 21yrs
posted by Choctawman
14 comments posted 21yrs posted by Choctawman

Delta Benchtop Bandsaw

I have an old Delta benchtop bandsaw ( I think 4 inch??) and it needs either new rubber on the wheels or new wheels wit...
5 comments posted 21yrs
posted by woodgirl68
5 comments posted 21yrs posted by woodgirl68

What are these Delta hybrids?

I received a new Tool Crib catalog yesterday and hadn't looked at one in a while. Anyway I saw 3 different saws that lo...
8 comments posted 21yrs
posted by DontSpamMedukes909
8 comments posted 21yrs posted by DontSpamMedukes909

Link belts FS (maybe)

I am thinking of selling link belt material (Power Twist). This is Fenner, the good red stuff. I can sell it for $4.40...
0 comments posted 21yrs
posted by Jamien
0 comments posted 21yrs posted by Jamien

Woodcraft Store

Well, They did it to me again. Went to their store in Knoxville to purchase an item and for the third time in less than...
49 comments posted 21yrs
posted by GeraldR916
49 comments posted 21yrs posted by GeraldR916

Re: Jointing not quite with the grain?

Won't worry as much about exit defects if you clamp an inch and a half of soft scrap to the good wood. It takes the hit...
0 comments posted 21yrs
posted by george
0 comments posted 21yrs posted by george

Pls help identify mahogany type wood. Scented.

I'm restoring an English solid mahogany with rosewood veneer antique box. I'm no expert but I would guess its about 200...
17 comments posted 21yrs
posted by theartist
17 comments posted 21yrs posted by theartist

Re: Newbie question on cutting beadboard

> Hi. I have to cut 4x8 sheets of beadboard with a fine toothed circular saw. > If I'm not mistaken the blade rotates f...
5 comments posted 21yrs
posted by onlnlowe
5 comments posted 21yrs posted by onlnlowe

Re: Verita Hand Scrapers

> After years of watching David Marks do his thing with a scraper, i decided > it was time to buy one. I found a decent...
6 comments posted 21yrs
posted by dave
6 comments posted 21yrs posted by dave

Removing ding with a clothing iron

I read somewhere that you can remove a small ding in timber with a clothing iron? How can I do it? TIA, Lee W
2 comments posted 21yrs
posted by me
2 comments posted 21yrs posted by me

Ridgid Table saw

I just purchased a Ridgid portable table saw. It seems like a nice saw. However, I found the set up to be much more ext...
14 comments posted 21yrs
posted by phntmmike
14 comments posted 21yrs posted by phntmmike

Sumi ink for ebonizing

I've read a lot about using India ink for ebonizing wood, such as red oak, but also found Sumi ink at my local art stor...
0 comments posted 21yrs
posted by urg44
0 comments posted 21yrs posted by urg44