Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Polyurethane, mix and match

I have used Sherwin Williams oil based Satin Polyurethane on a large project. I do not like the appearance and want to...
5 comments posted 20yrs
posted by wsw1856
5 comments posted 20yrs posted by wsw1856

baseboard heaters in wood shop - safe?

I'm converting a 20' x 24' tool shed into a wood shop, adding all new electricity, benches, lighting, insulation, etc....
11 comments posted 20yrs
posted by mulkscf
11 comments posted 20yrs posted by mulkscf

bandsaw motor

I would like to replace the 3/4 HP motor on my bandsaw with a larger hp motor. Do I need to buy a Delta motor for a Del...
15 comments posted 20yrs
posted by morgand
15 comments posted 20yrs posted by morgand

Let's talk lighting

Awhile back I saw some threads talking about the ideal shop lighting setups. I saved some messages that really summariz...
11 comments posted 20yrs
posted by me
11 comments posted 20yrs posted by me

Parts for Powermatic 45 Lathe

Hello, Does anybody have a source for parts for a Powermatic 45 lathe? I am looking for a headstock indexing pin and an...
1 comments posted 20yrs
posted by grmpyoldad
1 comments posted 20yrs posted by grmpyoldad

Re: Blast Gate Actuators

> I'm in the process of running 120/240 VAC power as well as low-voltage > signal wiring to an underfloor grid in the c...
1 comments posted 20yrs
posted by ricksub
1 comments posted 20yrs posted by ricksub

Refacing a refacing job

Has anyone ever refaced a kitchen cabinet that had already been refaced once before? How difficult is it to remove the f...
2 comments posted 20yrs
posted by jsamsen
2 comments posted 20yrs posted by jsamsen

Hang doors in existing opening

We're replacing all the doors in an older home and as in many older houses the floors (and therefore the doorframes) ha...
16 comments posted 20yrs
posted by skfifield
16 comments posted 20yrs posted by skfifield

How to cut 16" miter joint?

I am building a 16" deep stand. The top and sides will be a miter joint. My RAS will only cut 15.5". Any way to get tha...
16 comments posted 20yrs
posted by Toller
16 comments posted 20yrs posted by Toller

Water tight deck over a room

I have a 10'x12' deck and want to enclose the lower area for a storage room. For this to work I need to have the deck s...
3 comments posted 20yrs
posted by tomh
3 comments posted 20yrs posted by tomh

Printmking For High School

http://www.princetonol.com/groups/iad/lessons/high/printmaking.htm I've just skimmed this so far but looks intriguing....
0 comments posted 20yrs
posted by Jakofalltrades
0 comments posted 20yrs posted by Jakofalltrades

Anyone know optical sensors

Good afternoon. 102F with a heat index of 125F here in NJ today... Death Valley, eat your heart out... I've got a custo...
10 comments posted 20yrs
posted by bob
10 comments posted 20yrs posted by bob

Amazon promo

Direct quote: "Through August 31 only, take $25 off your purchase of $199 or more of any items in our Tools & Hardware S...
0 comments posted 20yrs
posted by am15us
0 comments posted 20yrs posted by am15us

step molding

I recently replaced some indoor steps that were covered with wall to wall carpet.. I used composite wood steps clad wit...
2 comments posted 20yrs
posted by tolbiny
2 comments posted 20yrs posted by tolbiny