Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

ultra light mdf

Anyone have a source for ultralight MDF in the Knoxville area??? Tried woodfinder with no luck. TIA, Joe
2 comments posted 20yrs
posted by in
2 comments posted 20yrs posted by in

teak door

My dad was helping with the earthquake in Indonesia and while he was over there he got to know somebody who owned a fur...
3 comments posted 20yrs
posted by rinfo
3 comments posted 20yrs posted by rinfo

Tools for Woodwork???

Folks, Just bought a house and need to fix/re do a few things. Wanted to buy few good wood working tools first. I know...
16 comments posted 20yrs
posted by djadav2004
16 comments posted 20yrs posted by djadav2004

My jury-rigged jigsaw table thing

If you want a scroll saw, but your wallet suffers from a severe impaction, then a thing like this will either fill your...
15 comments posted 20yrs
posted by burright65
15 comments posted 20yrs posted by burright65

Roy Underhill injured again.

I was watching his show this Sunday and saw where he had about 12 stitches in his right index finger. He was showing how...
32 comments posted 20yrs
posted by tom
32 comments posted 20yrs posted by tom

Delta 12 1/2" Surface Planer Question

I own a Delta 12.5" surface planer and have recently noticed that the unit is cutting unevenly. If I were to run a piec...
3 comments posted 20yrs
posted by michael.fischer
3 comments posted 20yrs posted by michael.fischer

v-tongue and grove router bit

I have been searching for something that may not be made. Have seen lots of v-tongue and groove router bits on the Inte...
1 comments posted 20yrs
posted by victorj
1 comments posted 20yrs posted by victorj

OT? - Woodworking MAYDAY (m'aidez)

I've set up portion of my web site as a place to share woodworking and shop ideas; and it's been satisfying to see that...
1 comments posted 20yrs
posted by mrdovey
1 comments posted 20yrs posted by mrdovey

poplar stained ....

Don't ask why, but I have a refinished older dresser with a couple of pieces of poplar that are viewable, and have been...
2 comments posted 20yrs
posted by larry.levinson
2 comments posted 20yrs posted by larry.levinson

How to identify old pressure treated lumber?

I am in the process of demolishing an old chicken coop. All of the wood has by now fully greyed, and none of it appears...
3 comments posted 20yrs
posted by andrewSPAMALOT
3 comments posted 20yrs posted by andrewSPAMALOT

OT: Baja house update

For those that asked, I put the pictures from our trip this weekend up today: http://www.davisbaja.com/sept-baja.htmHou...
23 comments posted 20yrs
posted by mac
23 comments posted 20yrs posted by mac

Dewalt 18 V Parts ?

Does anyone have a dead 18 volt Dewalt tool that they want to give away? I want to make a light that I can plug one of m...
1 comments posted 20yrs
posted by HPbyGDnospam
1 comments posted 20yrs posted by HPbyGDnospam

Worms in Ash boards

I have a number of Ash boards that I purchased a while back. When I went to use one, there seems to be worms in the woo...
5 comments posted 20yrs
posted by wood
5 comments posted 20yrs posted by wood

Walnut Knife Handle

I have a set of the Chicago Cutlery knives, and need to oil them after several years of use. I have some of the Seal-A-...
3 comments posted 20yrs
posted by lcottrell
3 comments posted 20yrs posted by lcottrell