Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

PING - Mekon & LonE

RE: ABPW Mekon, At least your fingers look to be whole, still. If all you may loose is a nail, then you are lucky. Hope...
1 comments posted 20yrs
posted by cedarsonny
1 comments posted 20yrs posted by cedarsonny

Question about Rockler lift caster

http://www.rockler.com/product.cfm?page=2383Can anyone tell me how much the step caster that is part of the above Rockle...
5 comments posted 20yrs
posted by cgallery
5 comments posted 20yrs posted by cgallery

Hemlock wood poisoning

Does anyone know if seasoned and dried hemlock has any undesirabl characteristics? I want to use hemlock because of its...
7 comments posted 20yrs
posted by victoria.2eq5m4
7 comments posted 20yrs posted by victoria.2eq5m4

TurboCad vs. AutoCad

Somebody wrote to me this past week about the difference between AutoCad and TurboCad. The difference is about $2400.00...
10 comments posted 20yrs
posted by notme
10 comments posted 20yrs posted by notme

DIY HVLP

I've talked (email) to a couple of the guys that have built their own HVLP turbine from a 3 stage vacuum motor and they...
6 comments posted 20yrs
posted by me7
6 comments posted 20yrs posted by me7

Changing finish

Ten years ago I made and installed red oak interior window sills. Minwax stain and clear lacquer finish. Now in need of...
3 comments posted 20yrs
posted by hiview68NO SPAM
3 comments posted 20yrs posted by hiview68NO SPAM

The Strength of M&T Joints

Pictures posted in ABPW. SWMBO and I had the privilege of revisiting Colonial Williamsburg a couple of weeks ago, our f...
2 comments posted 20yrs
posted by rp77469
2 comments posted 20yrs posted by rp77469

Airbrushing Polyurethane?

Has anyone tried putting on the final finish to a project using an airbrush as the application tool for either water ba...
15 comments posted 20yrs
posted by dhaan
15 comments posted 20yrs posted by dhaan

sliding sled

I have a craftsman table top 10 inch table saw. I want to make a sled for it, but the miter tracks have a little edge o...
14 comments posted 20yrs
posted by pattj
14 comments posted 20yrs posted by pattj

Cub Scout WoodDorking - Yippee

This is what really floats my boat these days. We divided up the projects for the year and we are going to spend three...
13 comments posted 20yrs
posted by notme
13 comments posted 20yrs posted by notme

Specific type of tubing for Exacta fence rails?

I recentlly bought an old Unisaw, and the Delta fence on it isn't that bad. But, the first time I had to make a real cu...
3 comments posted 20yrs
posted by over40pirate
3 comments posted 20yrs posted by over40pirate

Help: Bandsaw For Cutting Wood and Delrin

I need to cut wood and Delrin rods(up to 4" in diameter or square) into plates that are 2/16" to 1/4" thick. Can I get...
3 comments posted 20yrs
posted by Searcher7
3 comments posted 20yrs posted by Searcher7

Jet, Excata fence rail material>>

I recentlly purchased an old Unisaw, and the first time I went to make a "real" cut, other than teast cuts, discovered...
5 comments posted 20yrs
posted by over40pirate
5 comments posted 20yrs posted by over40pirate