Fan Heater talk

Nov 17, 2026 Last reply: 7 minutes ago 9 Replies
Saved reading
Jump to replies (9)

My garage is best described as: 100% Through-Flow Ventilation. It used to be a horse stable, for the pub that the house was originally. It not only has gaps between the slats, there is a small glass-less window high up on the wall behind the parked car. The whole building is about the size of three parked cars, but only one spot can be accessed by a vehicle, the rest is workshop and storage space. CPC are offering a 3kW electric fan, and I was wondering if this might enable me to work out there during the winter. I am now 76 years old, so winters are not kind, but I have stuff to do on my classic car, and at present, nearly half the year is unavailable.



I have over the years visited many garages and workshops with propane-powered 'jet-engine' heaters, this looks like a (very) poor cousin.



formatting link
Or:
formatting link
Does anybody have any experience with these things? I need to only heat the area where the car is, to work on it, not the whole building, although it's all open plan.


utm_medium=email&utm_source=website&utm_campaign=Christmas-161126&utm_content=HG01478-11&CMP=e- email-Christmas-161126-HG01478-11

n.b This product is only suitable for well insulated spaces or occasional use

So I'd say no unless you have a very cheap tariff for electric!

AVPX

I suspect that "This product is only suitable for well insulated spaces" gives the game away, as a 3kW fan-heater in a big draughty space will not do much at all. It'll possibly be OK just blowing at you.

3kW makes only a little impact on my much smaller garage with leakage only around the main door.

nib

It's pointless to try to heat a space with so many holes. Block the window and line the inside of the walls and ceiling with 50mm PIR "seconds".

A quick question to Gemini gave: "To heat and maintain a 10m × 10m × 3m space from 3°C to 15°C with thin, drafty timber walls, you will need a heater rated at roughly 14 kW to 16 kW (about 48,000 to 55,000 BTU/h). While warming the trapped air itself takes very little energy (1.26 kWh), thin timber conducts heat rapidly and gaps let warm air escape continuously. Your heater must constantly replace this lost heat."

You also need to consider how long it would take to get up to temperature.

utm_medium=email&utm_source=website&utm_campaign=Christmas-161126&utm_content=HG01478-11&CMP=e- email-Christmas-161126-HG01478-11

Aren't radiant (infra red) heaters used in such environments ? Heating up the surface rather than the air in between ?

That is a thought worth following, thanks.

Yes. It heats you rather than the air. Rather uncomfortable as it only heats the side of you near the heater. Aren't there heated suits you can wear? This is kind of what Martin Lewis is recommending.

formatting link

I found this:

formatting link
has some interesting items.

utm_medium=email&utm_source=website&utm_campaign=Christmas-161126&utm_content=HG01478-11&CMP=e-

I've seen them in tyre fitters, and my last company had them in the warehouse. This was the winter after they had to hire 4 1m fans to cool it down from 43C .....

Yup...

I use a wall mounted 2kW one in my workshop, controlled by an external stat. Normally the stat is set very low, but gives an occasional burst of heat to keep it around 10 deg C in there. That keeps it dry and tools rust free. If I want to work in there, it will get it up to a comfortable temperature in 15 - 20 mins of so...

(I also have a halogen radiant heater in there that can be used for quick directional heat - sometimes handy if you just need to feel warm, rather than heat the whole room)

One big caveat though, the place is insulated on all walls and the roof with 50mm PIR foam. Solid concrete slab base and a single glazed window. It is mostly air tight though.

So heating like that can work in the right circumstance. Enough insulation and reducing the number of air changes per hour is the key.

(you also get a less obvious benefit from the insulation - the internal wall temperature is kept a little higher, which instantly makes the place feel less cold and oppressive since you can feel that some heat is actually radiated back to you)

Trying to use convention heating in a draughty uninsulated space will be about as effective as trying to heat your garden! On the bright side that does make the cost of a cheap insulation job pay for itself very quickly!

The only way you can really do that is with radiant heat (think, the old dull red glowing element type of electric bar heater). That will heat you rather than the building directly. Perhaps a lined and heated tool cabinet to keep the tools nicer to handle etc.

Might also be worth looking at modern heated jackets. Most of the big brand tool makers do a range of jackets or body warmers that will take a Li-Ion battery. e.g:

formatting link

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required