Best Rated threads in Tools and Equipmentshow all threads

Subject Author Posted Replies
 
20" husqvarna 455 Chain tensioner is at the end of the adjustment screw with a brand new chain.
I have a husqvarna 455 chainsaw. The sprocket looks good and the bar looks good. The bar says 72 drive links .050 gauge and 3/8" pitch. I always buy stihl chains. I buy a brand new chain and the...
1
1
 
shop mate lathe
Looking for information on the Shop Mate Sabre Lathe Model 2610to
 
Craftsman mower model 917.370440 squeaks while mowing and smokes when first starting it.
What is wrong?
 
i want to cut a cast iron sewing machine in half for book ends
what do i cut it with ?
 
measure .006 inches?
I'm looking for a common household item that I could use to measure .006 inches for a spark plug gap.
 
Can't get the blades off, are they left handed screws?
I have a john deer riding mower, 22 hp, and need to take the blades off but the cap screws won't budge. Are they left handed, or just stuck?
2
2
 
Oil for Gcv 160 Troy Built pressure washer
Gcv 160 Troy Built Pressure washer uses what type oil?
 
belmont barber chair hydralic repair
chair is stuck at top will not release to go down
 
I need parts for a Westway folding ladder and I can not find the company .
I have a 4 section folding ladder and one of the folding mechanisms does not unlock very easy, I have oiled it and it just does not unlock very easy. I have tried to find parts without any success,...
 
sears professional table saw 922124
Looking for the specifications of the two Motor capacitors: Run Cap (224E OR91725) and Start Cap (224C OR91723) The Start Cap on my saw destroyed itself and obliterated any identification and specs...
 
how to change bulb
How do I change. Bulb in my zero trace lithium -ion led flashlight the serial number is TL1KPZ I think its charging right but it has been stoped a couple times
 
craftsman mower 37041 ran out of gas, now won't start
craftsman mower 37041 ran out of gas, I refilled the gas tank, however the mower will not start. I've had this mower less than 2 weeks.
 
sears pressure washer 580.768310 info? Please!!!!
I have a sears pressure washer model# 580.768310, with a tecumseh 6.25hp # 640276. Engine number is 143.006204, family# YTPXS.1951BB, and D.O.M is 0161 K. its 195cc. Is sears only place for parts? Ive...
1
1
 
Has anybody sucessfully opened and repaired a Sunterra 1250 pond pump?
I have a submersible Sunterra 201250 pond pump (bullet nose), it has become a little noisy and is now cutting out continuously. It is not hot to the touch. If I spin the shaft it will start turning...
4
4
 
U-tube Lightning pro concrete mixer , tool looks great
Saw this new tool on u tube. Makes mixing bagged concrete a breeze compared to using a hoe or shovel. Also don't need a powered mixer .
 
Need replacement fence part 1349805 for Delta 10" compound miter saw model 36-075
I have a Delta 10" compound power miter saw model 36-075 and need a replacement fence--part # 1349805. It is an obsolete part, so I am hoping someone has a broken saw that they are willing to piece...
 
30 amp fuse keeps blowing on 18hp Kohler engine on my Craftsman garden tractor.
The 30 amp fuse keeps blowing on my 2000 Craftsman garden tractor with a 18hp Kohler engine. I have replaced the switch and solenoid and checked all wiring for damaged insulation but all wiring looks...
 
2 cycle 5 horse tecomseh carb #640310 . will any other carb work on this ?
i found a few other carbs that look almost exact , like oregon carbs but can't cross ref it. the web says #640310 is used on model #hsk 845-8219b there has to be another less expensive carb that will...
 
Lefoo lf10-4h2 pressure swith for air compressor
I need a drawing or schematic to asemble this swith, i took it apart without realizing it was spring loaded so when I removed it from its bracket the parts came loose. Thanks
3
3
 
LA110 John Deere Lawn Tractor - Engine Binding Up While Trying to Start
My LA110 John Deere Lawn Tractor with a 19.5 hp Briggs and Stratton motor is having trouble strarting. The engine will crank about 3/4 of turn then seems to bind up. If I manually help the motor turn...