Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Sliding T-bevel, marking guage
1. A sliding T-bevel seems like it would be a useful markup tool. Any special reason they put a potentially blood-letting 45 degree point on the tail end of the blade (to help make it a combination...
23
|
14 years ago
|
23 | |
|
Re: OT Frost your nuts?
I'd like to see it resolved too, but I don't see it happening. Got the roof done but that's as far as ambition went. Maybe this summer I'll do more.
28
|
14 years ago
|
28 | |
|
HFT "Porta Band" Knock Off
These take the standard 44 7/8" blades. Has anyone owned one ? Did it last.
2
|
14 years ago
|
2 | |
|
Guidelines for posting FS items
I posted this msg on alt.woodworking group and didn't get a reply how about here? >What are the guidelines for posting woodworking equipment items for sale?
12
|
14 years ago
|
12 | |
|
Router sled for cutting curve/dip?
I can imagine a router solution with the router supported ahead of and behind the bit, on a pair of curved tracks - but I suspect you might find clamping and supporting the workpiece (especially for...
11
|
14 years ago
|
11 | |
|
Semi-gloat, shaves and scrapers
Two Stanley 151 spokeshaves, one Sweetheart, the other new One No 60 spokeshave, Sweetheart One No. 80 card scraper, no blade, dated 6-2-14 One No. 82 scraper, no blade One No 66, Feb 9.86, no blade...
10
|
14 years ago
|
10 | |
|
Campfire/firepit seating ...
Saw this in a magazine some time back and memorized the dims, can't remember which one, but whoever you are, thanks for the inspiration. to make sure it works before passing it on and today is the...
—
|
14 years ago
|
— | |
|
Pilotless counterbore
I'm in need of making about a 5/16 counter bore into hard wood only about 1/16th deep. Exact measurements are not needed but it should be fairly flat with no pilot hole(or something that is no more...
7
|
14 years ago
|
7 | |
|
Re: Frost your nuts?
So, are you going to address the evidence any time soon?
47
|
14 years ago
|
47 | |
|
I WON BOTH!!!!!!
... the35-pocket bucket organizer AND the 3-piece screw extractor set. From the Handyman Club of America. All I have to do is sign up. -Zz
9
|
14 years ago
|
9 | |
|
Outside corner molding -- walnut?
May have to but would rather not if the price is right. and I can get it.
13
|
14 years ago
|
13 | |
|
Ping Garage Woodworks
I just noticed something that you may be interested in putting together. In the ShopNotes current magazine, Vol.19 Issue 109 there is a 4 page article on building a cart that holds your shop vacuum,...
1
|
14 years ago
|
1 | |
|
CPO Woodworking review
Delta-PC listed as one of their online sellers, but when I was thinking about ordering I couldn't find much information about them. Since they were referred by the Delta-PC web site, I ordered anyway....
2
|
14 years ago
|
2 | |
|
Furniture, with humor ...
Why HVAC Ductwork Design Matters - Straight Line Designs
12
|
14 years ago
|
12 | |
|
Small but fun project.
I had to figure it out, hence the delay in answering your question re cost. The mirror was $ 350.00, the rest $ 1800.00 (Not including tap, paint/ paper/wallsponge and all that rot. That was the...
18
|
14 years ago
|
18 |