Re: Wood Burning Stoves

You will have to do a bit of research ( try searching on Google ), but AFAIK, you need a non-combustible hearth of approved type on which to stand the thing, plus you probably need a class A flue, which I think means a chimney more than 16 feet tall and at least 6" square, or something like that anyway. You can get a woodburner at Machinemart, or at various specialist fire shops, you'll have to work that one out yourself ( lots of these shops have webpages for you to browse through ). Woodburners are throttleable in order to adjust the burn rate so yes, you can avoid draughts by closing the damper ( check on the model you are considering buying ). You will have to fit the flue to a non-combustible fireback, which needs sealing in the fireplace aperture. It would be wise to check that your chimney does not leak before you install a fire, by placing a smokebomb-thingy in the fireplace ( get them from a fire shop ), then dashing from room to room trying to see if any smoke is issuing out of your walls!
Andy

up.
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

I was trying to think of where I'd come across the Alaska Woodburner or Cabin Stove. I wonder if it was a booklet I saw there years ago. It consisted of 2 x 45 gallon drums, one atop the other.
The wet/poor quality fuel burned in the first tin then the tarry gas and etc burned in the top one.
In theory.
That Centre for Alternative Tech. is a great day out though. Highly recommended. One day I shall live in a manner that embodies all those ideals but at the moment, give me the simple life.
As for sources of fuel. The small stuff that comes out of the "chipper" in a timber yard if there is one locally is a far better fuel than the off-cut blocks they sell, easier to handle and probably cheaper too.
If you know anyone that is in the window replacement business they might be willing to supply you. For me; I would get a sawdust burner. This is how to make one:
Two drums one that fits inside the other say one at 10 and a 25 gallon one. Spot weld or rivet a shelf for the inner tin to stand on that gives room to cover the outer one and allow flame and smoke to exhaust the top of the inner.
Cut a vent in the side of the outer (near the bottom and leave one edge so that it acts as a door. (Unless you are really clever and make a proper sliding grate.))
Cut a hole through the centre of the inner tin, about 3" dia. but this size depends on how much you need to burn. (A smaller hole will do just as well, then if you wish to enlarge it.....)
Above the stand, another vent in the outer will take a chimney pipe. (4" cast iron guttering or whatever you can snaffle.)
Draught:
The only air access is through the bottom vent and, with the top on, the only egress is the one just above the shelf. Fit a 3" x 3" (or whatever) in the centre of the inner tin and pack around it with saw-dust. Remove the 3" x 3" and put a lid on the outer.
Light a piece of paper and stuff it in the bottom vent. (We never had barbeque lighters in those days.) The flame should be drawn up through the saw-dust igniting it in a slow burn that draws flame and smoke between the two tins. Hopefully it will burn all the tar before it solidifies in the pipe.
The workshop where this was used was a dismal little weather enclave that gave me hours of fun first thing of a cold morning in winter. However once going, it only needed restocking once or twice. This was done over glowing dust embers we might have cooked potatoes on had the shop next door not sold real bread and good, old fashioned ham.
You could use this thing outside as a barbeque if you wanted to try it out. It will also burn logs. If you are using a dustbin for the outer make sure the zinc is burned away before utilising the lid for cooking.
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload
On 18 Aug 2003 08:17:32 -0700, snipped-for-privacy@hotmail.com (Michael McNeil) wrote:

I wouldn't waste my time on oil drums. They're thin steel, wood burner flue gas is corrosive, and they just don't last that long. If I'm going to make a stove, I use propane cylinders.
I was impressed by this as a design. http://www.sense3d.com/bigoven.html A similar "two drum" idea, but double-walled and with the upper one as an oven.
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

I hope you realise what you are saying is verging on criminal. But more to the point dangerous. (The cylinder has to be burned or something to render it safe as gas can be absorbed into the steel or what did I hear about that.....)
There is quite a difference in the cubic capacities too, isn't there?
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload
On 18 Aug 2003 23:16:30 -0700, snipped-for-privacy@hotmail.com (Michael McNeil) wrote:

So are most things. Taking a car and driving it away might be legal - unless it's your car.

Indeed. Why not read my FAQ on how to reduce the hazards of doing this ?

No, you'd prefer to post half-assed and downright dangerous "advice" about "burning" the cylinder. Are you really advising people to do this ?

So what ? I don't particularly want a 40 gallon stove anyway.
Add pictures here
<% if( /^image/.test(type) ){ %>
<% } %>
<%-name%>
Add image file
Upload

HomeOwnersHub.com is a website for homeowners and building and maintenance pros. It is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.