Woodworking Forum

  1. Home
  2. Woodworking Forum
51626 Threads Posts
to

Worth reading in Woodworking Forum

Replacement Motor for 14" Delta

I would like to replace the motor with a large, more powerful unit. I think the present motor is BAD as it slows dow in...
20 comments posted 18yrs
posted by gooeytarballs
20 comments posted 18yrs posted by gooeytarballs

Dewalt DC500 Vacuum Doesn't Aspirate

It sucks w/o the filter in place but then speeds up and doesn't suck at all with the filter in place. I cleaned up dirt...
4 comments posted 18yrs
posted by cauchy128
4 comments posted 18yrs posted by cauchy128

Varnish for outdoor service?

I'm looking for advice on alternate varnish with good UV protection. Last project used Bristol 2 part, but at $80 a qua...
1 comments posted 18yrs
posted by cavelamb
1 comments posted 18yrs posted by cavelamb

When Functional &Improvisation Collide

The August 2008 issue of WOODWORK has an interesting article on Susan Working which contains a side bar titled The Art...
3 comments posted 18yrs
posted by charlieb
3 comments posted 18yrs posted by charlieb

Shim washers

I've done a Google search for packets of shim washers and found that I can buy, in quantity, various shim washers. What...
17 comments posted 18yrs
posted by mjmwallace
17 comments posted 18yrs posted by mjmwallace

O/T: Things are "Toasty"

Things were warm here in SoCal today. 96F outside my window at 10:00AM this morning and it isn't even summer yet. Sever...
17 comments posted 18yrs
posted by lewhodgett
17 comments posted 18yrs posted by lewhodgett

Fun with nail gun

I posted on ABPW... pay attention folks! John
0 comments posted 18yrs
posted by grossboj.nospam
0 comments posted 18yrs posted by grossboj.nospam

Hole Saw recommendations?

I'm in the market for a hole saw kit for cabinet installation and was wondering if any of you all had any strong prefer...
3 comments posted 18yrs
posted by JayPique
3 comments posted 18yrs posted by JayPique

Forstner bits

I wanted to counterbore several 3/4" holes about an eighth of an inch deep in 3/4" plywood. I bought a set of Forstner...
40 comments posted 18yrs
posted by infodex
40 comments posted 18yrs posted by infodex

Seeking a Special Chop or Cut-Off Saw

The other day, some cable TV show about trucks (I think) had this new low RPM, no dust cut-off saw that also allowed mi...
8 comments posted 18yrs
posted by bob
8 comments posted 18yrs posted by bob

Yet another compound miter question

have done some searching and will continue to do so, but if anyone has some tips it would be greatly appreciated: I'm s...
3 comments posted 18yrs
posted by mdevenney1
3 comments posted 18yrs posted by mdevenney1

Walnut Desk Project and Sketchup PDF file

I am building a Walnut desk for a customer and posted on a.b.p.w. two low resolution pictures of the desk as it stands...
22 comments posted 18yrs
posted by removespamlcb11211
22 comments posted 18yrs posted by removespamlcb11211

HVLP & Latex: Follow-Up

First, I want to send a HUGE THANK YOU to Robert (a.k.a. "nailshooter41") for selflessly sharing his knowledge on this...
5 comments posted 18yrs
posted by none
5 comments posted 18yrs posted by none

Ping Upscale - Bench for Wheelchair users

I think it's Upscale that uses a wheelchair and was mentioning what General had done with table saws. Chris Schwartz ha...
7 comments posted 18yrs
posted by Tanus51
7 comments posted 18yrs posted by Tanus51

Exterior doors. Steel of Fiberglass?

Not exactly a woodworking question, but who better to ask. I'm in the market for 5 new entry doors for my house. Choise...
17 comments posted 18yrs
posted by wcs94
17 comments posted 18yrs posted by wcs94