Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Engineer's square

How do the Groz engineer's squares measure up for setting up a TS, BS, etc? Rockler has them (set of 3) on sale for $29...
111 comments posted 16yrs
posted by Bill_NOSPAM
111 comments posted 16yrs posted by Bill_NOSPAM

Delta Bench Grinder

Is the following bench grinder one of the better choices for plane irons and miscellaneous use? I was concerned that it...
11 comments posted 16yrs
posted by Bill_NOSPAM
11 comments posted 16yrs posted by Bill_NOSPAM

Jawhorse.

Anybody tried one? It looks to be a knockoff of the Triton Superjaws without the $400.00 price tag.
19 comments posted 16yrs
posted by cmagers
19 comments posted 16yrs posted by cmagers

Kudos to the Woodrat folks

I may have mentioned that I acquired a pre-owned Woodrat from CL. The previous owner advised that one of the cauls that...
9 comments posted 16yrs
posted by TD
9 comments posted 16yrs posted by TD

SOT: Spring for refinished chair

I have an antique office chair, all refinished. But I can't find a replacement spring for the rocker mechanism. It is v...
6 comments posted 16yrs
posted by billnews2
6 comments posted 16yrs posted by billnews2

OT: That was pretty bad.

Watched the AMA's tonight. With few exceptions, it was bad. Awful in fact. Where was (were) Kings Of Leon? Adam Lambert...
3 comments posted 16yrs
posted by counterfitter
3 comments posted 16yrs posted by counterfitter

Early annual carving project

Because the kids & grandkids schedules, we had our annual carving project early. This Turky was road-killed and then ap...
2 comments posted 16yrs
posted by dlwinterburn
2 comments posted 16yrs posted by dlwinterburn

Shop Video Tour

I have been wanting to make a video tour for a while and finally did today. My little place of serenity. Check it out: h...
1 comments posted 16yrs
posted by bgrella
1 comments posted 16yrs posted by bgrella

Zinsser Sanding Sealer vs. Shellac

Does anyone know the relative pound-cut of the standard shellac? I've found that the sealer is a 2lb. cut on their webs...
22 comments posted 16yrs
posted by JayPique
22 comments posted 16yrs posted by JayPique

Update on Unisaw setup..

Thanks to all that gave tips for my friend and his "new to him" Unisaw.. I saw him tonight and he said that he read my...
0 comments posted 16yrs
posted by mac
0 comments posted 16yrs posted by mac

Video of My Table Saw Out-feed Table

Thanks for all the pictures and ideas. I made a folding version and it turned out great. Instead of taking pictures and...
38 comments posted 16yrs
posted by mike
38 comments posted 16yrs posted by mike

Flutes continued

Ok, I tried making a few stopped flutes which terminate with a taper using a wedge as discussed in a previous thread. (...
29 comments posted 16yrs
posted by bgrella
29 comments posted 16yrs posted by bgrella

A couple of small upgrades for my shop:

http://www.youtube.com/watch?v=CVNUJGi9sLg&feature=rec-HM-rev-rnhttp://www.youtube.com/watch?v=F3bUommA84w&feature=relat...
8 comments posted 16yrs
posted by kac
8 comments posted 16yrs posted by kac

Christmas is coming

Well,its only 4 Weeks away ! What are you making as Cgristmas Gifts ?? . Personally I have several Turned desklamps, re...
3 comments posted 16yrs
posted by Dotcom70
3 comments posted 16yrs posted by Dotcom70