Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Good Harbor Freight product IMHO

I know you have to be very carful buying from Harbor Freight and much of their stuff is pretty bad. I once had one of t...
7 comments posted 14yrs
posted by bwx200
7 comments posted 14yrs posted by bwx200

O/T: May Day

Lighten things up a bit. Enjoy Lew ---------------------------------------- This is the story of the poor blonde flying...
3 comments posted 14yrs
posted by sails.man1
3 comments posted 14yrs posted by sails.man1

OT, Life in the twilight zone

Life takes some unexpected ugly twist sometimes. Dad has been in ICU for 9 weeks with little hope of a good outcome, go...
16 comments posted 14yrs
posted by basilisk
16 comments posted 14yrs posted by basilisk

Getting rid of a Radial arm saw

So there was a Recall of the Sears 10 inch Radial Arm Saw. Years ago they offered a price that wasn't worth it. But now...
13 comments posted 14yrs
posted by godsword
13 comments posted 14yrs posted by godsword

Earlex HV6900

Just received my Earlex HV6900 Spray Station HVLP Paint Sprayer from Amazon.com Can't wait to use it on Monday on a Pain...
3 comments posted 14yrs
posted by rich
3 comments posted 14yrs posted by rich

What happened to NYW online episodes?

It seems like there have been no 'new' NYW online episodes since #812 (Nest of Drawers) that played back in mid-October...
8 comments posted 14yrs
posted by NOSPAM
8 comments posted 14yrs posted by NOSPAM

Tip for cleaning old Latex brushes

I used my Latex brush for Zinsser's BIN Primer/Sealer which suggest either Ammonia (50:50 with water) or alcahol for cl...
12 comments posted 14yrs
posted by NOSPAM
12 comments posted 14yrs posted by NOSPAM

Beginner

I have made a lot of mitered picture frames and other type work so have no problem in accuracy from that point of view....
5 comments posted 14yrs
posted by keith_nuttle
5 comments posted 14yrs posted by keith_nuttle

Somebody remind me

Of the technique for boring equally-spaced holes in boards that will be the sides of a bookshelf, for the little posts t...
17 comments posted 14yrs
posted by heybub
17 comments posted 14yrs posted by heybub

Router planing sled with a mortising bit?

I am putting together a router sled to plane down an end grain cutting board this weekend as the belt sander is not rea...
6 comments posted 14yrs
posted by jtpryan
6 comments posted 14yrs posted by jtpryan

What is it? Set 417

Just posted my set for this week: http://55tools.blogspot.com/Rob
20 comments posted 14yrs
posted by rhvp65
20 comments posted 14yrs posted by rhvp65

Power cord clips

When using a sander, it would be nice to be able to easily and temporarily clip the power cord to the vacuum hose. Does...
20 comments posted 14yrs
posted by puckdropper(at)yahoo(dot)com
20 comments posted 14yrs posted by puckdropper(at)yahoo(dot)com

PING: Mike Marlow - Extreme Makeover

https://picasaweb.google.com/111355467778981859077/ChezPouletGentle?authkey=Gv1sRgCKnyycz194WjPg#5680905070630320898What...
3 comments posted 14yrs
posted by kac
3 comments posted 14yrs posted by kac

Table Saw Safety & The CPSC

These folks tell you where to lodge your opinion. I Know you have one....
36 comments posted 14yrs
posted by LD
36 comments posted 14yrs posted by LD

Cutting Panels Large For A Small Table Saw

Hi, I need to cut some 20" x 17" plywood panels on a small table saw whose fence only goes to 12". In the past I rough...
9 comments posted 14yrs
posted by abbybrown
9 comments posted 14yrs posted by abbybrown