Woodworking Forum

  1. Home
  2. Woodworking Forum
51625 Threads Posts
to

Worth reading in Woodworking Forum

Motor Tablesaw

My Delta Unisaw has been working fine for fifteen years. Now all of sudden when I push the start button the motors spin...
16 comments posted 14yrs
posted by bb
16 comments posted 14yrs posted by bb

In search of a box joint

Bought a jig and it seems to work much better than my home-made one. Got out my old Craftsman dado set and cut a few qu...
19 comments posted 14yrs
posted by gwr95
19 comments posted 14yrs posted by gwr95

O/T: Paper Or Plastic

"Paper or plastic"? A question that is being asked less and less these days here in SoCal. More and more cities here in...
15 comments posted 14yrs
posted by sails.man1
15 comments posted 14yrs posted by sails.man1

Minwax Date Codes

Just thought I'd share this, in case anyone else has ever wondered how to read the date codes on Minwax cans. Can of Mi...
46 comments posted 14yrs
posted by doug_at_milmac_dot_com
46 comments posted 14yrs posted by doug_at_milmac_dot_com

O/T: Warm Enough

Take your choice, wild fires in the west or oppressive heat waves thru out much of the rest of the country, global warmi...
175 comments posted 14yrs
posted by sails.man1
175 comments posted 14yrs posted by sails.man1

OT. summer activities:

Its almost rodeo season and country fair time , my better half and I hookup the old RV. and do the circuit throughout t...
6 comments posted 14yrs
posted by sjimkj
6 comments posted 14yrs posted by sjimkj

Woodcraft? Honest reviews?

I noticed that my reviews of Woodcraft products don't make their reviews if I rate them poorly, only when I rate them w...
7 comments posted 14yrs
posted by nospam.nospam.com
7 comments posted 14yrs posted by nospam.nospam.com

Centerline of oblong

How can I locate the center-line on one of the flat sides of an oblong piece of wood?
3 comments posted 14yrs
posted by gcotterl
3 comments posted 14yrs posted by gcotterl

OT.garage entry:

I would like to install some type sensor ,indicator that signals when I have entered my garage far enough to close the d...
33 comments posted 14yrs
posted by sjimkj
33 comments posted 14yrs posted by sjimkj

I just finish another job~

I started this project near the end of last month. My customer wanted simple red oak book cases that would hold loads o...
40 comments posted 14yrs
posted by lcb11211
40 comments posted 14yrs posted by lcb11211

O/T: Amazing

Today's vote by the SCOTUS was amazing. Now let the fun and games begin. Lew
182 comments posted 14yrs
posted by sails.man1
182 comments posted 14yrs posted by sails.man1

Uh-oh

More on Project Thickness Sander: So I finished gluing up the plywood discs to the 1 inch steel shaft. Bearings arrived...
6 comments posted 14yrs
posted by Nomore
6 comments posted 14yrs posted by Nomore

Urns for veterans

My woodworkers club is making urns for unclaimed veterans remains... John For Some time NWA has been making URNS for th...
1 comments posted 14yrs
posted by grossboj.nospam
1 comments posted 14yrs posted by grossboj.nospam

Delmhorst G-22 moisture meter

$3.50, thrift store. Works fine, includes extra points, couple of scuffs on the meter, normal wear, clamshell case is in...
4 comments posted 14yrs
posted by fatherhaskell
4 comments posted 14yrs posted by fatherhaskell

repair stationary belt sander

It sounds like a bearing is gone on my Craftsman 6"x48" stationary belt san= der. I have taken enough off to expose and...
1 comments posted 14yrs
posted by l-lopez
1 comments posted 14yrs posted by l-lopez