Woodworking Forum

51629 Threads Posts
to

Marples blue handles factory grinding?

I got a set of Marples chisels based on word of mouth recommendation, opened the set, and was disappointed in the inita...
12 comments posted 22yrs
posted by mslatter
12 comments posted 22yrs posted by mslatter

advice please

I need to make the top part of a chair, where the spindles conect into. I need to bend a 1X6X24 inch board. what is the...
7 comments posted 22yrs
posted by Camoman
7 comments posted 22yrs posted by Camoman

Looking for stop hinges in Phoenix...any ideas?

Hi all, Anyone in the Phoenix, AZ area know where to find small box hinges that stop at a fixed position, e.g. 95 degre...
9 comments posted 22yrs
posted by alltheseworlds
9 comments posted 22yrs posted by alltheseworlds

Tenoning jig advice needed

Hi everyone. I'm trying to determine which after-market tenoning jigs will work with Craftsman miter slots. I know, I k...
32 comments posted 22yrs
posted by bm.cooper
32 comments posted 22yrs posted by bm.cooper

Bending warped wood

I have a very old dresser probably 50 years or older. One of the side panels on a drawer is warped at the back causing...
1 comments posted 22yrs
posted by mj.789
1 comments posted 22yrs posted by mj.789

having a problem with stain!

hi everyone... I glued a half-lap joint together. However, when it came down to staining, the stain was unable to fully...
4 comments posted 22yrs
posted by ah10201
4 comments posted 22yrs posted by ah10201

Split Cherry

Undertook a pretty simple project to continue my introduction into wood working. A small table made from 3/4 cherry I f...
1 comments posted 22yrs
posted by nospam
1 comments posted 22yrs posted by nospam

Grizzly Guide Block Holders

Does anyone know where I can get guide block holders for a Grizzly G0555 bandsaw? I've ordered them through Grizzly, bu...
4 comments posted 22yrs
posted by tomwojecknospam
4 comments posted 22yrs posted by tomwojecknospam

DIY Wisconsin -- Speakerbuilding Inquiry

This is a repost for any who missed my earlier message seeking those interested in speaker DIY in Wisconsin. Since the...
1 comments posted 22yrs
posted by lon
1 comments posted 22yrs posted by lon

Porter-Cable 80 gal air compressor question.

After purchasing the air compressor I do not see a standard tank outlet in the side of the tank anywhere. Its a vertica...
4 comments posted 22yrs
posted by rmo7hatespam
4 comments posted 22yrs posted by rmo7hatespam

WTB: Stanley framing square

Not just any old Satanley square, though. Here's a copy of a WTB request I sent to the oldtools forum. So far, no bites...
8 comments posted 22yrs
posted by wmengineer
8 comments posted 22yrs posted by wmengineer

PING Bay Area Dave

Well, I got my Powermatic 14" bandsaw set up....wasn,t to much trouble. But, I waited 2 months to get the saw, back-ord...
1 comments posted 22yrs
posted by snowdog
1 comments posted 22yrs posted by snowdog

Borg

Ok, I read it in the FAQ and I see it a lot in postings. Aside from Star Trek, what in the heck is the "Borg?" Home Depo...
10 comments posted 22yrs
posted by jamckelvey
10 comments posted 22yrs posted by jamckelvey

Titebond III yet ?

Is is available yet ? Anyone tried it ? Are you waiting on it ? Why ? jim bailey
3 comments posted 22yrs
posted by jimREMOVETHIS
3 comments posted 22yrs posted by jimREMOVETHIS

Wiring up electric motor for shop sander

Hi All, I've picked up an electric motor in a garage sales, its a Emerson, model K55HXDPZ-7023 HP 3/4, volt 115, RPM 10...
10 comments posted 22yrs
posted by kracus1
10 comments posted 22yrs posted by kracus1