Woodworking Forum

51629 Threads Posts
to

Source for drill guide bushings

Looking for drill guide bushings of the serrated, press-in type - not the kind that screw into universal 1-20 holders....
1 comments posted 22yrs
posted by jvogel20_remove_this_
1 comments posted 22yrs posted by jvogel20_remove_this_

Question: old ext. cords

I have an old short (12') extension cord. It is, by far, my favorite. Unfortunatley it is has worn out. The cord is tot...
9 comments posted 22yrs
posted by garyk
9 comments posted 22yrs posted by garyk

todays weather in Atlanta

Yesterday the local weather man was warning those with allergies to beware of the high pollen count. I can't remember a...
11 comments posted 22yrs
posted by mikehide
11 comments posted 22yrs posted by mikehide

Mini-Max S45 and Carter Guides

I just got an older model S45 at an auction and the top bearings and the entire bottom guide assembly need replacing. T...
2 comments posted 22yrs
posted by cghunter
2 comments posted 22yrs posted by cghunter

Using mixed wood types...

I want to build furniture / cabinets, but the range of materials here is poor. The materials are very limited. Solid ha...
6 comments posted 22yrs
posted by John Hewitt <jhewitt
6 comments posted 22yrs posted by John Hewitt <jhewitt

Can sanding substitute for planing?

I have 2 30"x24" panels (made of three pieces each) that I need to surface. They are 13/16" and will probably end up a...
5 comments posted 22yrs
posted by toller
5 comments posted 22yrs posted by toller

Lettering Product

Does anyone know of a product that can put letters on wood, finish w/ an outdoor finish and then have withstand the elem...
3 comments posted 22yrs
posted by kgiles
3 comments posted 22yrs posted by kgiles

Breaker and wire size?

Hi, I think I've finally decided on my new table saw, the Grizzly model 1023S, 3hp cabinet saw. Should I go with a 20 or...
13 comments posted 22yrs
posted by tony1158REMOVE
13 comments posted 22yrs posted by tony1158REMOVE

Aluminum Throat Plate

I recently inherited an old table saw that uses a thin (3/32") throat plate made from aluminum. I'm going to make a "lo...
4 comments posted 22yrs
posted by jeffsd
4 comments posted 22yrs posted by jeffsd

FS: or trade 4" joiner knives

I have a set of three sharp Craftsman #9-2291 4" joiner knives. I have a 6" joiner and no joiner knife stretcher. Will s...
2 comments posted 22yrs
posted by shakascaregiver
2 comments posted 22yrs posted by shakascaregiver

Recommended drill press speeds

I just purchased a Jet 17MF drill press. It has belts that let you run it from 200 rpm to 3200+ rpm. I'd like to find s...
7 comments posted 22yrs
posted by dsnyder
7 comments posted 22yrs posted by dsnyder

Rockler sure foot aluminum bar clamps

Has anyone used the Rockler sure foot aluminum bar clamps? How do they compare with Bessey clamps? Do the clamp heads s...
6 comments posted 22yrs
posted by cjscurria
6 comments posted 22yrs posted by cjscurria

ANVIL MOUNTING STAND

http://www.warnerknives.com/anvil_stand.htmJOATTo preserve liberty, it is essential that the whole body of the people a...
0 comments posted 22yrs
posted by Jakofalltrades
0 comments posted 22yrs posted by Jakofalltrades

Lasik

This may or may not be construed as OT. I am asking this same question on several different forums and discussion group...
64 comments posted 22yrs
posted by perrylep
64 comments posted 22yrs posted by perrylep

Tear-out on oak - repairing the edge

What do y'all use to fix an edge on a piece of wood? I had a bit of splintering in spite of climb-cutting with the rout...
6 comments posted 22yrs
posted by JayPique
6 comments posted 22yrs posted by JayPique