Woodworking Forum

51629 Threads Posts
to

table saw surface

I am looking for recommendations on how to maintain a cast iron table saw surface. The saw will sit in the garage where...
10 comments posted 22yrs
posted by jstein
10 comments posted 22yrs posted by jstein

On This Day In Wreck History

This is guaranteed to get 'em crawling out of the woodwork, Bill.... "Lonesome and amorous neanderthal desires curvilin...
7 comments posted 22yrs
posted by tjwatson1
7 comments posted 22yrs posted by tjwatson1

Yahoooo!!! New Tools

If you was the R E Quick Transit van speeding down the road this moring, it was me on the way to Sears. I was up early...
12 comments posted 22yrs
posted by sockman
12 comments posted 22yrs posted by sockman

starrett straightedge

I found this on ebay. Normal disclaimers - not associated with the seller. I remember periodic questions about straight...
21 comments posted 22yrs
posted by steinrm
21 comments posted 22yrs posted by steinrm

R/D 46-111 lathe

I have a Rockwell/Delta 46-111 lathe that I haven't used in probably 10 or 15 years and now have a need to turn some le...
3 comments posted 22yrs
posted by phnyphrmSPLINTER
3 comments posted 22yrs posted by phnyphrmSPLINTER

Wooddorking Near Spring Lake, North Carolina?

I'm going to be in Spring Lake, North Carolina (near Fort Bragg/Fayetteville) for about a week later on this month and...
4 comments posted 22yrs
posted by tjwatson1
4 comments posted 22yrs posted by tjwatson1

Butternut

As I understand Butternut is a close relative to Walnut. Workability is supposed to be the same as Walnut. Wifey wants...
14 comments posted 22yrs
posted by johnedwards123
14 comments posted 22yrs posted by johnedwards123

Waterstones vs. Scary Sharp

At crossroads now between using waterstones or SS as my main means of sharping. In any case I`d like to do this once and...
12 comments posted 22yrs
posted by johnedwards123
12 comments posted 22yrs posted by johnedwards123

Makita SCM Adjustment

When I set my Makita LS1013 SCM there is a little play when the saw is placed in a positive stop such as a right angle...
0 comments posted 22yrs
posted by glenduffNOSPAM
0 comments posted 22yrs posted by glenduffNOSPAM

Finished my project... Have a look!

Finally got this project finished. Took me nearly three months, but it paid off. I am so happy with the result, I might...
16 comments posted 22yrs
posted by da
16 comments posted 22yrs posted by da

Kitchen almost done

Well, I have been quiet for a while...Christmas was Busy...yep..for all us toymakers. But after the rust, came the lull...
0 comments posted 22yrs
posted by john
0 comments posted 22yrs posted by john

Conan the Liber-one, you online?

If so, would you please give me a ping via e-mail. try: d c s 2 k a t o p t u s n e t dot c o m dot a u I need to ask y...
0 comments posted 22yrs
posted by wizofoz2k
0 comments posted 22yrs posted by wizofoz2k

where can i find used tools

hi everyone... what are some good places and websites to acquire good used or refurbished tools? thanks
2 comments posted 22yrs
posted by ah10201
2 comments posted 22yrs posted by ah10201

Recockulous jointer FS on Ebay

16" Jointer w/2 extra sets of knives. As of 1 a.m. EST (or is it EDT?) there were no bids at $850. David Marks, Schmavi...
1 comments posted 22yrs
posted by phildcrowNOSPAM
1 comments posted 22yrs posted by phildcrowNOSPAM

Web site updated

I just updated my web site with some better shop pictures and the completed workbench drawers. Home page, the updated li...
10 comments posted 22yrs
posted by nospam
10 comments posted 22yrs posted by nospam