Woodworking Forum

51629 Threads Posts
to

Plywood types

After reading up on table saw jigs (sleds, aux fences, etc), the materials most often recommended seems to be baltic bi...
3 comments posted 22yrs
posted by rick --dot-- s --at-- comcast.
3 comments posted 22yrs posted by rick --dot-- s --at-- comcast.

Q: bandsaw tuning

I have a 14" Jet bandsaw that as of recently refuses to cut in a straight line. The blade consistently drifts at about...
15 comments posted 22yrs
posted by axr67
15 comments posted 22yrs posted by axr67

Plans for a hidden bed

In our cottage we have one smaller bedroom where a full size double bed overwhelms the room. I would like to make a bed...
3 comments posted 22yrs
posted by ig
3 comments posted 22yrs posted by ig

Source for interior doors

Hi, I am helping a friend with a remodel job that includes a complete kitchen remodel along with replacement of all of...
0 comments posted 22yrs
posted by areidjr
0 comments posted 22yrs posted by areidjr

wing chair upholstery

I am in the middle of making a couple of Chippendale repro wing chairs . The frames will be good quality [for me at lea...
2 comments posted 22yrs
posted by mikehide
2 comments posted 22yrs posted by mikehide

Dust doors for Delta tools- Who needs one?

I called Delta yesterday for some dust doors as I have several used resale machines missing the plain flat panel doors...
8 comments posted 22yrs
posted by catruckman
8 comments posted 22yrs posted by catruckman

Semi OT?? TurboCAD v10 installation error message

Folks - I know we've got some techies out here and I am HOPING for some help.... I just purchased and installed TurboCA...
7 comments posted 22yrs
posted by johnmoorhead
7 comments posted 22yrs posted by johnmoorhead

Hardwood/Exotic lumber supply near Fargo ND?

Anyone have a source for this stuff near Fargo ND....Looking mostly for some small amounts of exotic woods for inlays, a...
1 comments posted 22yrs
posted by crazydan
1 comments posted 22yrs posted by crazydan

Drill driver (screwdriver) bits

Does anyone have a preference for drill driver bits, specifically Robertson #2. I've been driving quite a few screws th...
15 comments posted 22yrs
posted by me7
15 comments posted 22yrs posted by me7

Which 12" Compoud Miter to buy....?

Hello everyone, This is my first post to the group and I hope it will be a successful one. We've been in our new house...
9 comments posted 22yrs
posted by
9 comments posted 22yrs posted by

On rabbets, plane vs saw

Greetings, Just got Ian Kirby's "The Complete Dovetail" from interlibrary loan. In the description of the double lap do...
9 comments posted 22yrs
posted by nospam
9 comments posted 22yrs posted by nospam

Best was to sell Table Saw?

Hey all, What's a good way to sell a table saw? My wife gave me the green light to buy a new cabinet saw, so I want to...
16 comments posted 22yrs
posted by piomice
16 comments posted 22yrs posted by piomice

On a lighter note, Brewed Lumber?

Well, I was at Lowe's today pricing items for a bid that I am doing and walking past the stacks of PT lumber I saw, "Bo...
5 comments posted 22yrs
posted by removespamlcb11211
5 comments posted 22yrs posted by removespamlcb11211

thoopid pulley size/power/mojo question

Folks - Lawdy! I am still futzing with my old craftsman 6" jointer and am going to swap motors out for MORE POWER. The...
5 comments posted 22yrs
posted by johnmoorhead
5 comments posted 22yrs posted by johnmoorhead

FAQ?

Could someone direct me to the FAQ? Thanks, Snidely
5 comments posted 22yrs
posted by Muttly
5 comments posted 22yrs posted by Muttly