Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Question about Excalibur Blade Guards

Folks - I've had the Excalibur overarm blade guard setup for several months and have a question... I have the guard set...
0 comments posted 21yrs
posted by johnmoorhead
0 comments posted 21yrs posted by johnmoorhead

How well does poplar take stain?

I have a little project upcoming that will want some nice stained wood bits. I don't need to match any existing wood bi...
32 comments posted 21yrs
posted by j.michael.elliottAT
32 comments posted 21yrs posted by j.michael.elliottAT

when to use 1/2" vs. 3/4" veneered plywood?

The usual Google searches didn't turn up much on this. Is there a rule of thumb on when to use one vs. the other? It's...
13 comments posted 21yrs
posted by kenkyee
13 comments posted 21yrs posted by kenkyee

ABPW Question

Folks - Is APBW archived anywhere? I don't check as often as I should and posts disappear pretty quickly. I don't see it...
1 comments posted 21yrs
posted by johnmoorhead
1 comments posted 21yrs posted by johnmoorhead

Help: Refinishing Bar tables (high traffic)

Hello! I have aprox 20 small bar tables that need to be refinished and I am not sure how to start. The tables are about...
5 comments posted 21yrs
posted by j_lynds
5 comments posted 21yrs posted by j_lynds

RHYTHM BOX

http://www.imaging.robarts.ca/~amulder/wood/p.beatbox/Woodwork Safely, Jim Barry http://www.DownloadWoodworkingPlans.com
4 comments posted 21yrs
posted by jim
4 comments posted 21yrs posted by jim

Metric brad-point drill bit

I'm looking for a 14mm brad-point bit. Rockler is sold out until February. Who else is a good source for things like thi...
12 comments posted 21yrs
posted by j.michael.elliottAT
12 comments posted 21yrs posted by j.michael.elliottAT

General international 50-185

Well I got my new TS on Thursday, and broke the box open shortly after. I had the saw on base within 2-3 hours. As atat...
2 comments posted 21yrs
posted by nopostage
2 comments posted 21yrs posted by nopostage

G'day boys from Phully

G'day boys and girls . . . Had a contact from me old mate Jummy yesterday - which was very nice. Some of you may still...
7 comments posted 21yrs
posted by nangalery
7 comments posted 21yrs posted by nangalery

OH WOW! Sears did it!

I would normally not have much to say about Sears other than to lament the declining quality and complain about the pus...
0 comments posted 21yrs
posted by lazarus
0 comments posted 21yrs posted by lazarus

DOVETAI JIG - PDF

http://www.popularwoodworking.com/features/fea.asp?id=1087JOATWe cannot direct the wind, but we can adjust the sails. -...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

CHISEL SHARPENING JIG

http://www.am-wood.com/june98/chiseljig.htmlJOATWe cannot direct the wind, but we can adjust the sails. - unknown
1 comments posted 21yrs
posted by Jakofalltrades
1 comments posted 21yrs posted by Jakofalltrades

best way to turn firewood into slabs?

I'm sure someone here has done this...I have a pile of salvaged maple firewood, where the figure is too beautiful to bu...
17 comments posted 21yrs
posted by nigeltufnel
17 comments posted 21yrs posted by nigeltufnel

ROUND BASKET

http://www.woodworksandcrafts.com/projects/index.htmlJOAT We cannot direct the wind, but we can adjust the sails. - unkn...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

reconditioning old machinery question

I've just been given an old (50+ years) drill press. It appears to be in great condition with little use, but the movin...
1 comments posted 21yrs
posted by jerryshaw
1 comments posted 21yrs posted by jerryshaw