Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Advise for deck over patio with little clearance

I want to build a deck overtop of an existing 8x10 concrete patio. The main problem is that the existing patio sits abo...
3 comments posted 21yrs
posted by mike
3 comments posted 21yrs posted by mike

Accessory available?

I have a Craftsman table saw, model # 137.218250. If you look underneath the saw, the blade housing, which is on one si...
3 comments posted 21yrs
posted by bub209
3 comments posted 21yrs posted by bub209

shop vac, Mitersaw

Ok, so Ive got an "auto switch" from sears and Ive got a Bosch 3915 sliding miter saw (13 amp). All I need is a shop va...
1 comments posted 21yrs
posted by phntmmike
1 comments posted 21yrs posted by phntmmike

Re: Bridge City Tool works does it again

Too little, too late, I suppose, but for my own part I've been using these BCTW scrapers for over 2 years now in my bus...
1 comments posted 21yrs
posted by oldcountry
1 comments posted 21yrs posted by oldcountry

opinions on running DC pipe needed

I have researched for awhile on the placement of the DC pipe.(I have a 1.5hp DC with 1 micron bags) Some people say to...
11 comments posted 21yrs
posted by taxconsultant
11 comments posted 21yrs posted by taxconsultant

Where to get 4x4s?

I see a lot of shop tables with 4"x4" stock for the legs. *Where* do you get non-treated 4x4 stock nowadays? The best t...
32 comments posted 21yrs
posted by David_Pike
32 comments posted 21yrs posted by David_Pike

Lee Valley 4" Double Square

I just got this for Christmas, and it now has a permanent place in my apron. Accurate to .001", this is my new portable...
5 comments posted 21yrs
posted by JayPique
5 comments posted 21yrs posted by JayPique

Small gloat

200 piece drill/screw-driver bit set, normal price £30 ~ $60, reduced 3 times to £3 ~ $6... Woolworths!
0 comments posted 21yrs
posted by the10ths.50th
0 comments posted 21yrs posted by the10ths.50th

Shellac Source

Once upon a time, long ago (it doesn't seem that long ago), I purchased some excellent PaddyLac. I haven't had much tim...
6 comments posted 21yrs
posted by David_Pike
6 comments posted 21yrs posted by David_Pike

Why did Grizzly raise their prices?

Is it because of the dollar being devalued? When the dollar goes up again will they lower their prices? I think they ar...
74 comments posted 21yrs
posted by bob
74 comments posted 21yrs posted by bob

JOINTING WITH A PLANER

I've seen the posts about planing with a jointer, do I need a jointer, do I need a planer, and so on. I'm wondering if...
4 comments posted 21yrs
posted by Jakofalltrades
4 comments posted 21yrs posted by Jakofalltrades

Suitability of MDF to make riser block for mortiser

I need to make a 4" riser block for my Delta Benchtop Mortiser and am wondering about the suitability of MDF to cut and...
3 comments posted 21yrs
posted by tillman.stevens
3 comments posted 21yrs posted by tillman.stevens

Tsunami Aid - Tools?

I would think that there must be a need for all kinds of woodworking, carpentry and other trade tools in all of the cou...
8 comments posted 21yrs
posted by NjOrSePdAM
8 comments posted 21yrs posted by NjOrSePdAM

Finally saw Nahmie for first time in 20 years...

Flipping channels for SWMBO, came across a woodworking show on PBS. Ah, there's Nahmie. I was surprised he used his TS...
78 comments posted 21yrs
posted by dmmcintyr
78 comments posted 21yrs posted by dmmcintyr