Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Miter Saw Stand

I'm looking to build a miter saw stand for my saw. Has anyone built one or know where I can get plans for one? ksm
6 comments posted 21yrs
posted by kevinmain
6 comments posted 21yrs posted by kevinmain

HEPA type filter for Hoover Wet/dry vac

Does anyone know if there is a HEPA filter that will fit on a Hoover wet/dry vac?
2 comments posted 21yrs
posted by jimltz
2 comments posted 21yrs posted by jimltz

A little help here? !! Keyholes.....

Greetings All! I am attempting to rout two keyholes on the back of a shaker shelf to hang the shelf with. Its a flush m...
8 comments posted 21yrs
posted by granite_skies
8 comments posted 21yrs posted by granite_skies

Larger copper pipes for dust collection?

If I ground my PVC dust collection ducts to my water pipes, will I need to sweat bigger copper tubing since my dust col...
20 comments posted 21yrs
posted by <sell1892
20 comments posted 21yrs posted by <sell1892

Website Enhancement

Chiefly for handworkers are five new items in the Mortising & Tenoning section dealing with the design and use of some f...
4 comments posted 21yrs
posted by seethesig
4 comments posted 21yrs posted by seethesig

Mitre Saws - Dewalt or Makita?

I have recently purchased a property that requires a full make-over. To save money i intend to carry out the vast major...
12 comments posted 21yrs
posted by john-turner
12 comments posted 21yrs posted by john-turner

Scraper Plane Edge Prep

I recently acquired a Stanley #12. To make a long story short, I proceeded to butcher the scraper edge, and will need t...
11 comments posted 21yrs
posted by bml_in_co
11 comments posted 21yrs posted by bml_in_co

Table Saw Miter Gauge Help or Suggestions?

I am looking at this miter gauge: http://www.incra.biz/Products/Miter2000.htmlAnyone have any experience and some feedb...
15 comments posted 21yrs
posted by Xlat_999NOSPAMMING
15 comments posted 21yrs posted by Xlat_999NOSPAMMING

router table repost

Original post didn't show up . I have decider to build a router table instead of getting a shaper. I will be using the...
1 comments posted 21yrs
posted by akransom
1 comments posted 21yrs posted by akransom

mubango?

A lumberyard has mubango for $2/bf. Anyone tried this? (In a post below I referred to "African Cherry". Since the lumber...
5 comments posted 21yrs
posted by toller
5 comments posted 21yrs posted by toller

Air Dry vs, Kiln Dry

I have an opportunity to purchase 200 board feet of "air dried" white oak for about $1.50 per board foot. The wood has...
4 comments posted 21yrs
posted by john
4 comments posted 21yrs posted by john

please help>>Delta truck box key??

A local thrift store has a big plastic Delta truck box that should fit my '82 F-100 pickup (the kind that goes across t...
5 comments posted 21yrs
posted by paulmbedard
5 comments posted 21yrs posted by paulmbedard

Re: Rhapsody In BLO

Tom Watson wrote in news: snipped-for-privacy@4ax.com: > In a previous thread I talked about a highboy that I am gettin...
10 comments posted 21yrs
posted by gmadsen
10 comments posted 21yrs posted by gmadsen

Stanley 271

I stand corrected again... Here's an unused Stanley 271 on eBay. With Photos
5 comments posted 21yrs
posted by puzzled2
5 comments posted 21yrs posted by puzzled2

African Cherry

A lumberyard about 3 hours away from me is advertising African Cherry for $2/bf. From what I have read, it is a great w...
5 comments posted 21yrs
posted by toller
5 comments posted 21yrs posted by toller