Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Fein Turbo II/III vs dust collector

I have a 1hp dust collector that's rated at 650cfm. Will the Fein Turbo II or III which are rated at 116cfm and 126cfm...
8 comments posted 21yrs
posted by knotbob
8 comments posted 21yrs posted by knotbob

Re: Will shellac lock in traces of wax?

>I decided I need to put an additional coat of water borne poly over a >drawer front (I need to darken it slightly). I...
0 comments posted 21yrs
posted by Please_keep_it_in_the_newsgrou
0 comments posted 21yrs posted by Please_keep_it_in_the_newsgrou

Shop Vacuum Question

A debate has started at one of our local woodworking stores which someone may be able to help with. Ques: when the inta...
4 comments posted 21yrs
posted by cduke7nospam
4 comments posted 21yrs posted by cduke7nospam

Re: Any Online Sources?

> Any favorite online sources for sandpaper products and hard and soft woods? > These things seem to be vacant or enorm...
1 comments posted 21yrs
posted by ahem
1 comments posted 21yrs posted by ahem

TS Setup/alignment questions

I was messing around with my relatively new and unused dial indicator today to verify alignment of my table saw and cam...
42 comments posted 21yrs
posted by dontspamme
42 comments posted 21yrs posted by dontspamme

anybody ever buy from the CPO guys?

I found a company online that sells refurbished tools http://bosch.cpotools.com/http://www.cpowoodworking.com/http://ww...
2 comments posted 21yrs
posted by richard
2 comments posted 21yrs posted by richard

Non-Dremel rotary tool.

I'm looking to buy a rotary tool to sand and detail small parts (dense foam and plastic). I've seen some cheaper rotary...
9 comments posted 21yrs
posted by byoung
9 comments posted 21yrs posted by byoung

Plate jointer

I want to buy a Plate Jointer and what I thought would be an easy decision, Has turned into a "Spec" nightmare. I'm lean...
10 comments posted 21yrs
posted by browndogmail
10 comments posted 21yrs posted by browndogmail

Questions about air-drying cedar...

I just ordered some 1/2" & 3/4" x 6" width and 2"x8"x8' eastern red cedar, green. I'm planning on using it for deck pla...
2 comments posted 21yrs
posted by ronaldjangel
2 comments posted 21yrs posted by ronaldjangel

Rise/run ratio for straight staircase

Hi all, A little background: We're redoing the stairs in our 1865 house. They were replaced in the 1920s or so and we'r...
7 comments posted 21yrs
posted by scobiewan
7 comments posted 21yrs posted by scobiewan

Planer Blade Alignment Tolerance

I have a DeWalt DW733 planer. I just changed the blades for the first time, using the DeWalt magnetic alignment guides...
11 comments posted 21yrs
posted by newstemp
11 comments posted 21yrs posted by newstemp

A Good Read?

-------------------------------------------------------------------------------- Posted on Sun, Mar. 20, 2005 Carpenter...
13 comments posted 21yrs
posted by notme
13 comments posted 21yrs posted by notme

Careful with that router...

I was routing out the shapes of the feet on my Shaker table in what I feel confident was a safe manner when I picked up...
6 comments posted 21yrs
posted by phildcrowNOSPAM
6 comments posted 21yrs posted by phildcrowNOSPAM

Very dumb idea, Two riser kits on band saw?

Hello all, I was working at the Kitchener Wood Show yesterday and I had a guitar maker who needed 14" of resaw, but a s...
38 comments posted 21yrs
posted by kklaric
38 comments posted 21yrs posted by kklaric