Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Refinishing furniture with paint sprayer

I have a number of wood items that I plan to sand down and paint with a new paint sprayer I bought. My question is this...
4 comments posted 21yrs
posted by jasonandpamela
4 comments posted 21yrs posted by jasonandpamela

OT - joke

I'm sure this will be considered politicall incorrect by some, and really wind up some of the too tight people. I don't...
8 comments posted 21yrs
posted by Jakofalltrades
8 comments posted 21yrs posted by Jakofalltrades

Silver on Walnut

Hi I need to fix a small silver plaque (approx 2"*1") to a walnut rifle stock and I would appreciate ideas on the best...
4 comments posted 21yrs
posted by stephen
4 comments posted 21yrs posted by stephen

Using 1" thick cedar decking okay?

I'm trying to decide whether to go with inexpensive pressure-treated evergreen wood decking or low cost 1" thick (appro...
18 comments posted 21yrs
posted by kmoiarty35
18 comments posted 21yrs posted by kmoiarty35

Finishing kitchen cabinet

What's the best way to glue and finish kitchen cabinet? The case is made of maple and birch plywood and is to be finish...
3 comments posted 21yrs
posted by agalkin
3 comments posted 21yrs posted by agalkin

Crown molding installation question

I am about to install crown molding in my house but I have never done that before. I think I got the cutting part down...
34 comments posted 21yrs
posted by silkb
34 comments posted 21yrs posted by silkb

Crwon molding installation question

I am about to install crown molding in my house but I have never done that before. I think I got the cutting part down...
0 comments posted 21yrs
posted by silkb
0 comments posted 21yrs posted by silkb

BBQ Side Table

Another request for a plan ? groan, multiple groans. I want to build a side table for the BBQ. Typical BBQ height [ ~30...
4 comments posted 21yrs
posted by jhewitt
4 comments posted 21yrs posted by jhewitt

lumber selection for 118"x45" bay window roof

I am trying to build bay roof over the large bay window I installed. What is the proper lumber size to use for this pro...
3 comments posted 21yrs
posted by orodionov
3 comments posted 21yrs posted by orodionov

Wooden Bathtub

Any recommendations on the type of wood to use for a wooden bath tub, I've read that Teak and Redwood are a couple of t...
6 comments posted 21yrs
posted by jfisher
6 comments posted 21yrs posted by jfisher

square head--not square drive--screws

Most of the door hardware in my tudor-style house is secured with square-headed woodscrews (not square drive); they're...
2 comments posted 21yrs
posted by eag111
2 comments posted 21yrs posted by eag111

table saw blade size

I had an old Ward's table saw that used nine inch blades - it conked out. Bought a new ten inch saw - can I use the nin...
5 comments posted 21yrs
posted by wjwheeler
5 comments posted 21yrs posted by wjwheeler

Which Baldor motor

I have a Sears 10" table saw that is about 15 years old and it has a basic 1.5 hp Sears motor that I would like to upgr...
16 comments posted 21yrs
posted by mdfranci
16 comments posted 21yrs posted by mdfranci

Railing Baluster Spacing

I'm constructing a deck railing with 4"x4" posts, 2"x4" rails, and 1/2" copper balusters. For reasons I won't go into,...
8 comments posted 21yrs
posted by daz
8 comments posted 21yrs posted by daz

FS-Clausing 8520 Milling Machine

Hi Guys, I hope I'm not violating the rules of this NG by posting this. I have a Clausing 8520 that I am ready to list...
0 comments posted 21yrs
posted by jbacc
0 comments posted 21yrs posted by jbacc